A.J.Antunes 9700610 Owner'S Manual Download

Page: 7 / 20

UFC-420/440 water Filtration system

P/N 1010908 Rev. A 03/12

A.J. Antunes & Co.

Unpacking

1. Remove the system and all packing materials

from the chipping carton.

2. Remove all packing materials and protective cov-

erings from the system

3. Remove the information packet. To prevent any

delay in obtaining warranty coverage, fill out and

mail the warranty card.

nOte: If any parts are damaged, contact antunes

filtration technologies ImmeDIatelY at 1-800-253-

2991 or 1-630-784-1000.

equipment setup

General

When placing the unit into service, pay attention to the

following guidelines:

• Make sure power to the unit is off.

• Do not immerse cord or plug in water.

• Keep cord away from heated surfaces.

electrIcal

Ensure that the line voltage corresponds to the stated

voltage on the units specification label. Make sure that

the plug on the power cord from the system and the

outlet match. For proper operation, and to ensure the

highest quality water from the system, make sure that

the system is not connected to a switched electrical

outlet.

plUmbInG

nOte: this unit is designed to use tap water not

to exceed 104°F (40°C).

The UFC-420 and UFC-440 systems use the following

connections (Figure 1):

• Water Inlet

3/4” NPT

• Permeate (Product Water)

3/4” NPT

• Drain

3/4” NPT

InstallatIOn

When making a plumbing connection to the system,

remember to use a back-up wrench on the supporting

plumbing. Always use a good quality, approved, pipe

sealant or thread seal tape on pipe threads. Be careful

not to get the pipe sealant inside the pipe when making

the connections.

Do not

over tighten the connections. It is recommend-

ed that plastic fittings be used when connecting to the

plastic connections of the system. This will reduce the

possibility of cracking the connections due to overtight-

ening.

If soldered plumbing is used, do not apply heat to, or

near, the filtration system. The use of union (o-ring

seal) connections is highly recommended for ease of

installation and future servicing.

sUGGesteD tOOls anD sUpplIes fOr InstallatIOn

The following tools and supplies are suggested to make

the installation easier:

• Screwdriver

• Drill with bits

• Strap wrench

(up to 6” diameter)

• Tape measure

• Two gallon bucket

• Fresh 5 1/4% liquid

chlorine bleach

• Adjustable wrenches

• Pipe wrenches

• Level

• Pipe dope or thread

seal tape

Summary of Contents for 9700610





















Search results

Summary of Contents for 9700610

Reviews:

Related manuals for 9700610

Brands by name

Popular brands

A.J.Antunes 9700610, Owner'S Manual

Search results

Summary of Contents for 9700610

Reviews:

Related manuals for 9700610

Brands by name

Popular brands