background image

RAPID TOASTER VCT-200

5

P/N 1010710 Rev. N 02/13 

McDonald’s

Throughout this manual, you will find the following safety words and symbols that signify important safety issues with 

regards to operating or maintaining the equipment.

WARNING 

 

GENERAL WARNING.  Indicates information impor-

tant to the proper operation of the equipment.  

Failure to observe may result in damage to the 

equipment and/or severe bodily injury or death.

WARNING 

 

ELECTRICAL WARNING.  Indicates information 

relating to possible shock hazard.  Failure to 

observe may result in damage to the equipment 

and/or severe bodily injury or death.

CAUTION 

 

GENERAL CAUTION.  Indicates information impor-

tant to the proper operation of the equipment.  

Failure to observe may result in damage to the 

equipment.

WARNING 

 

HOT SURFACE WARNING.  Indicates information 

important to the handling of equipment and parts.  

Failure to observe caution could result in personal 

injury.

IMPORTANT SAFETY INFORMATION

In addition to the warnings and cautions in this manual, use 

the following guidelines for safe operation of the unit.

 

•  Read all instructions before using equipment.

 

•  For your safety, the equipment is furnished with a prop

-

erly grounded cord connector.  Do not attempt to defeat 

the grounded connector.

 

•  Install or locate the equipment only for its intended 

use as described in this manual.  Do not use corrosive 

chemicals in this equipment.

 

•  Do not operate this equipment if it has a damaged cord 

or plug, if it is not working properly, or if it has been 

damaged or dropped.

 

•  This equipment should be serviced by qualified person

-

nel only.  Contact the nearest Roundup authorized ser-

vice facility for adjustment or repair.

 

•  Do not block or cover any openings on the unit.

 

•  Do not immerse cord or plug in water.

 

•  Keep cord away from heated surfaces.

 

•  Do not allow cord to hang over edge of table or coun

-

ter.

The following warnings and cautions appear throughout 

this manual and should be carefully observed.

  •  Turn the unit off, disconnect the power source and 

allow unit to cool down before performing any ser-

vice or maintenance on the unit.

  •  The procedures in this chapter may include the use 

of chemical products.  These chemical products 

will be highlighted with bold face letters followed 

by the abbreviated HCS (Hazard Communication 

Standard).  See Hazard Communication Standard 

manual for the appropriated Material Safety Data 

Sheets (MSDS).

  •  The equipment should be grounded according to 

local electrical codes to prevent the possibility of 

electrical shock.  It requires a grounded receptacle 

with separate electrical lines, protected by fuses or 

circuit breaker of the proper rating.

  •  Bread may burn.  Therefore toasters must not be 

used near or below curtains or other combustible 

walls and materials.  Failure to maintain safe oper-

ating distances may cause discoloration or com-

bustion. 

  •  When installing conveyor belt wrap, be careful not 

to wrap it over the upper and lower support rods 

or permanent damage to belt will occur.  Make sure 

belt wrap is positioned UNDER the upper and lower 

support rods.

  •  Make sure both ends of belt wrap are aligned even

-

ly before installing belt wrap pin.

  •  Failure to use release sheets may result in damage 

to the equipment and loss of warranty coverage.

  •  All electrical connections must be in accordance 

with local electrical codes and any other applicable 

codes.

  • 

WARNING ELECTRICAL SHOCK HAZARD.  

FAILURE TO FOLLOW THESE INSTRUCTIONS 

COULD RESULT IN SERIOUS INJURY OR DEATH.

- Electrical ground is required on this appliance.
-  Do not modify the power supply cord plug.  If 

it does not fit the outlet, have a proper outlet 

installed by a qualified electrician.

-  Do not use an extension cord with this appli-

ance.

-  Check with a qualified electrician if you are in 

doubt as to whether the appliance is properly 

grounded.

Summary of Contents for 9200500





























Reviews: