background image

13

WARNING!

 Upon removal, cover the battery pack’s 

terminals with heavy-duty adhesive tape. Do not attempt to 

destroy or disassemble.

General maintenance

Avoid using solvents when cleaning plastic parts.  Most plastics are 

susceptible to damage from various types of commercial solvents and 

may be damaged by their use.  Use clean cloths to remove dirt, 

dust, oil, grease, etc.

WARNING!

• To avoid serious personal injury, always remove the  

battery pack from the tool when cleaning or performing  

any maintenance.
• When servicing, use only identical replacement parts.  

Use of any other parts may create a hazard or cause produc

t damage. To ensure safely and reliability, all repairs  

should be performed by a qualified service technician.
• It is not recommended to use compressed dry air to  

clean the driver. If cleaning with compressed air is the  

only method available, always wear safety goggles or  

safety glasses with side shields when using compressed 
air to clean the tool.  If the operation is dusty, also wear  

a dust mask.
• Do not at any time allow brake fluids,gasoline,  

petroleum - based products, penetrating oils,etc, to come i

n contact with plastic parts.  Chemicals can damage, 

weaken or destroy plastic which may result in serious  

personal injury.

Batteries

The battery pack is equipped with Lithium-ion rechargeable batteries.  

The duration of use from each charge will depend on the type of work 

performed.
The batteries in this tool have been designed to provide maximum 

trouble-free life.   Like all batteries, they will eventually wear out. Do 

not disassemble the battery pack or attempt to replace the batteries. 

Handling of the batteries, especially when wearing rings and Jewelry, 

could result In a serious burn.
To obtain the longest possible battery life, read and understand the 

operator’s manual.
• It Is good practice to unplug the Charger/Adapter and remove the 

Lithium-ion battery pack when not In use.

For Lithium-ion battery pack storage longer  
than 30 days:

•  Store the Lithium-ion battery pack where the temperature Is below 

80 “F (26°C) and free of moisture.

• Store Lithium-ion battery packs in a 30%-50% charged condition.
•  Every six months of storage, fully charge the Lithium-ion  

battery pack.

• Exterior may be cleaned with a cloth or soft non-metallic brush.

Battery pack removal and preparation for recycling

To preserve natural resources, please recycle or dispose of batteries 

properly.  This product contains lithium-ion batteries. Local, state, or 

federal laws may prohibit disposal of lithium-ion batteries in ordinary 

trash. Consult your local waste authority for information regarding 

available recycling and/or disposal options.

WARNING!

 Upon removal of the battery pack for 

disposal or recycling, cover the battery pack’s terminals 

with heavy-duty adhesive tape. Do not attempt to destroy 

or disassemble the battery pack or remove any of its 

components.  Lithium-ion batteries must be recycled or 

disposed of properly. Also, never touch the terminals with 

metal objects and/or body parts as a short circuit may result 

. Keep away from children.  Failure to comply with these 

warnings could result in fire and/or serious injury.

To ensure safety and reliability, all repairs should 
be performed by a qualified service Agent

Waste disposal

The product must not be discarded with normal household waste.   

It must be disposed of properly.

Touch_IM_ED8.indd   13

22/10/13   4:39:57 PM

Summary of Contents for T12 Series

















Reviews: