background image

4s2 Variable Temperature Thermal Sealer Service Manual 

 

 

 

4titude Ltd, The North Barn, Surrey Hills Business Park, Damphurst Lane, Wotton, Dorking, Surrey, RH5 6QT, UK 
Tel: +44 (0) 1306 884885  Fax: +44 (0) 1306 884886  [email protected]  www.4ti.co.uk

  

Page 1 

 

 

 

4s2 VARIABLE TEMPERATURE THERMAL SEALER 

SERVICE MANUAL 

 
 

This manual is intended to be used as a guide to maintaining the HT121TS thermal sealer. It is valid for 

the units with S/N higher than 42256. 

The information contained in this document is subject to change without notice. 

This document is for information only, manufacturer accepts no liability for errors contained herein or for 

incidental or consequential damages with the furnishing, performance, or use of this material. 

 

If not otherwise specified, each reference to names or belongings is purely casual and has the purpose 

to illustrate the product here described. Contents of this publication may not be reproduced in any form 

or  by  any  means  (including  electronic  storage  and  retrieval  or  translation  into  a  foreign  language) 

without prior agreement and written consent from the copyright owner. 

 

All rights are reserved. 

Summary of Contents for 4s2















Reviews: