4IPNET OWL530 Quick Installation Manual Download

Page: 19 / 26

Quick Installation Guide

OWL530

Outdoor AP/Bridge/CPE

ENGLISH

- 15 -

Step 5:

Configure WDS (Wireless Distribution System) Settings (Optional)

To extend the wireless coverage, OWL530 supports up to 8 WDS links per RF card for connecting wirelessly to

other WDS-capable APs, or peer APs. By default, all WDS profiles are disabled.



Click on the

Wireless

button on the main menu.



Select the

Repeater Settings

tab.



Choose

WDS

as the

Repeater Type



Choose the desired WDS profile:

(a) Enable

WDS

(b) Enter the

Remote AP MAC Address

(peer AP) and then Click

SAVE

If you are using another OWL530 as the peer AP, simply repeat the above-mentioned steps to configure

another peer AP(s).



Note:

On each and every configuration page, you may click

SAVE

to save the changes of your

configured settings, but you must reboot the system for the changes to take effect. After clicking

SAVE

, the following message will appear:

“Some modifications have been saved and will

take effect after APPLY.

”

Congratulations!

AP mode is now successfully configured.

Summary of Contents for OWL530

























Search results

Summary of Contents for OWL530

Reviews:

Related manuals for OWL530

Brands by name

Popular brands

4IPNET OWL530, Quick Installation Manual

Search results

Summary of Contents for OWL530

Reviews:

Related manuals for OWL530

Brands by name

Popular brands