3xLogic VSX-PTZ-2MP-EXT20 Installation Manual Download Page 2 | Manualshive

Page: 2 / 39

3xLogic VSX-PTZ-2MP-EXT20 Installation Manual Download Page 2

Installation Manual

| VISIX PTZ Network Camera

10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

2

Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the
dealer.

This manual applies to

VSX-‐PTZ-‐2MP-‐EXT20,VSX-‐PTZ-‐2MP-‐EXT, VX-‐2M-‐OP-‐PTZ20X

and

VX-‐2M-‐OP-‐PTZ30X

5-‐Inch Speed

dome PTZ network cameras.

This manual may contain    technical inaccuracies or printing errors.   The content is subject to   change without notice. The
manual will be amended if there are any hardware updates or changes.

DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or signaling aspects
of this product. UL has only tested   for   fire, shock or   casualty hazards as outlined in UL’s Standard(s)   for   Safety,
UL60950-‐1. UL Certification does not cover the performance or reliability of the security or signaling aspects of this
product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR   CERTIFICATIONS   WHATSOEVER REGARDING THE
PERFORMANCE   OR RELIABILITY   OF   ANY   SECURITY   OR SIGNALING RELATED FUNCTIONS   OF   THIS   PRODUCT.”

«
1
2
3
4
...
»

Summary of Contents for VSX-PTZ-2MP-EXT20








































Reviews:

No comments