manualshive.com logo in svg

3Ware 9650SE-8LPML-SGL, Manual

Share
Download
3Ware 9650SE-8LPML-SGL Manual Download Page 5

www.3ware.com

1

Chapter 1. Getting 

Started

The 3ware® 9650SE RAID controller provides these features: 

„

RAID 6 with simultaneous parity generation to maximize 
performance

„

8th-generation StorSwitch™ non-blocking switch fabric for 
maximum controller output

„

StreamFusion™ optimization of RAID 5 and RAID 6 disk 
accesses to maximize application performance under heavy 
loads

„

StorSave Battery Backup Unit (BBU) with write journaling to 
optimize data protection and performance (BBU must be 
purchased separately, and is not supported on 9650SE-2LP.)

„

RAID levels 0, 1, 5, 6, 10, 50, Single Disk, JBOD, and Hot Spare 

(RAID 6 and RAID 50 are available only with 3ware RAID 
controller models that have 8 or more ports)

„

PCI Express® x1, x4, or x8 connectivity

Contents of this Package

If you purchased a full retail kit, the following items are included:

„

This document, 

3ware 9650SE Serial ATA RAID Controller 

Installation Guide

„

3ware CD-ROM with driver, software, and additional 
documentation

„

Appropriate cables for the 3ware 9650SE model

„

For the 2-port model, two SATA interface cables, one for 
each port are provided.

Summary of Contents for 9650SE-8LPML-SGL














































Reviews:

No comments

Brands by name

Popular brands

Load more brands