3. ‘
3SIXT-M777’ should
then appear on the
Bluetooth device list on
your smartphone, tablet
or computer. Press/click it
and the Voice Prompt will
say “Phone X connected”
when pairing has been
achieved.
For more information and support visit
www.3sixtgear.com/support
READ FIRST
SAFETY & CARE
INFORMATION
• Use 3SIXT Bluetooth Studio Earbuds for its intended purpose
only. It is not a toy. Parental supervision is required for
children under 10 years old.
• Avoid excessive volume levels and prolonged periods of
listening. Do not use around road traffic.
• Do not drop, knock, disassemble or attempt to repair 3SIXT
Bluetooth Studio Earbuds.
• Do not immerse or put 3SIXT Bluetooth Studio Earbuds in
water and keep 3SIXT Bluetooth Studio Earbuds in a cool, dry
place and protect from dust.
• Do not expose 3SIXT Bluetooth Studio Earbuds to excessive
heat including sunlight and fire. Do not burn or incinerate
3SIXT Bluetooth Studio Earbuds or expose to extreme
temperatures (<0° or >45°).
• Wipe 3SIXT Bluetooth Studio Earbuds with a clean soft cloth.
Do not use chemicals or detergents to clean any part of 3SIXT
Bluetooth Studio Earbuds. Doing so may discolour or corrode
the materials.
1.
Insert the supplied Micro USB Cable (
5
) (Micro USB end)
into Bluetooth Studio Earbuds 5V input port (
3
).
2. Insert USB end of cable into the USB 2.0 port of
your 110/240V wall adaptor, laptop or PC.
3. The LED Indicator (
d
) will turn red when
charging, then blue when fully charged.
The indicator light will flash red when the battery level
is low, and there will be a voice prompt.
If left unused for 3 months, a fully charged battery will
lose its charge.
1.
Ensure your Bluetooth Studio Earbuds are fully charged
and separate the Bud Backs from each other to enter
‘standby/’ON’ mode’. The Voice Prompt will say “Power On”.
2. Once ‘ON’, press the Multi-Function Button (MFB) (
a
)
for 5 seconds to put the Bluetooth Studio Earbuds into
‘pairing mode’ with your device. ‘Pairing mode’ is evident
if the LED Indicator (
d
) flashes red then blue - the Voice
Prompt will say “Pairing”.
Within operating range (up to 10m), the Bluetooth
Studio Earbuds will automatically pair to your device
when Bluetooth is enabled and the Earbuds are separated
(‘ON’ position). This will be confirmed by the Voice Prompt
saying “Phone X connected”.
If the 3SIXT Bluetooth Studio Earbuds are left separated
for over 3 minutes without music playback or calls, it will
enter ‘standby mode’ to save battery life. In ‘standby mode’
you can make and receive calls or reinstate music playback
by pressing the MFB for the required operation (see Music/
Call Operation table). Disconnect the Earbuds from your device
to return your device to normal functionailty.
GETTING TO KNOW YOUR
BLUETOOTH STUDIO EARBUDS
CHARGING YOUR
BLUETOOTH STUDIO EARBUDS
TURNING ON & PAIRING YOUR
BLUETOOTH STUDIO EARBUDS
for the first time
PAIRING YOUR BLUETOOTH
STUDIO EARBUDS
every time after
STANDBY MODE
b
c
e
f
d
a
Gel Ear Clips
Earbuds
Controller
Volume up
Multi-Function
Button (MFB)
LED
indicator
Volume down
1
4
5
2
SMALL
LARGE
Ear Clips
SMALL ON DEVICE
Gel Earbuds
MEDIUM ON DEVICE
MEDIUM
(L & R)
LARGE
(L & R)
USB Charging
Port
(under Ear Clip)
3
Micro USB
Charging
Cable