background image

• If you have multiple small items, place them inside one pouch. After laminating, cut out. 

DO NOT cut pouch before laminating.

• Place SEALED end of pouch into the machine first, with the open end following behind.
• Irregular shapes, place towards the sealed end.
• Don't grab the hot end of the laminated item because it could deform. If deformation occurs, run 

the pouch through the machine again. Allow to cool before handling.

• Not meant to be used with a carrier pouch.
• If white blotches appear or the laminating pouch appears hazy, send the item, sealed end first, 

through the laminator again.

• Ensure that the mil thickness of the pouch you are using matches the setting you selected on the 

machine.

When finished press the power button to turn off the laminator. The laminator will turn itself off after a 

period of time. When cool, store laminator by returning input tray to its initial stored position. The power 

cord may be stored in the well on the bottom of the machine.

User Tips:

Operating Instructions:

Step 1: PREP

Make sure your machine is warm and ready to go.
• Place the laminator on a flat, secure, stable surface.
• The on/off button is located on the top of the machine and will glow green when turned on.
• Choose your pouch setting, either 3 mil, 5 mil, or 6 mil depending on the thickness of the pouch 

you are working with.

• The warm up time for this machine is approximately 1 minute, your machine is warm enough to 

start laminating once the ready light illuminates

Step 4: SEAL

• The laminated item will automatically exit the outlet of the 

machine. Do not pull the pouch through the laminator. 

• If the pouch does not feed correctly or jams, push the pouch 

reverse button located on the control panel to reverse the 

pouch back out of the laminator.

• Remove the pouch after it has stopped moving and allow to 

cool on a flat surface. Use caution, your project may be hot 

when exiting the machine.

• It may be necessary to laminate thicker items twice to 

completely seal the pouch.

Step 3: INSERT

Place the 

sealed end

 into the machine first with the open 

end following

• Check to make sure the pouch lines up to the opening to 

prevent uneven or angled feed through.

• Remove any objects that could get in the way of your 

project as it exits the machine

Step 2: PLACE

Place your project inside the laminating pouch
• Center your item(s) inside the pouch checking that 

you leave 1/8" laminate margin around the edges on 

each side for best sealing results.

• Tip: trim your project AFTER lamination.

Summary of Contents for Scotch PRO







Reviews: