3M MG-1000 Manual Download Page 68

Page: 68 / 90

58 • Ch. 6 Performing Field Repairs

75-0302-1450-8, Version 1

SST Transport and Burster Mechanism Manual

10. Remove and replace with a new PCB-2 Board.

Note:

When you replace the PCB-2 Board, make sure that the Joiner connecting the PCB-2

Board to the PCB-1 Board plugs properly into the PCB-1 Board.

11. Insert and tighten the M3 x 16 Phillips screws into the PCB-2 Board.

12. Plug in the flex cable connecting the PCB-3 Board to the PCB-2 Board.

13. Plug in the single track maghead (HP-1 only).

14. Replace the Appliance Base and tighten the two M3 x 8 Phillips screws.

Note:

When you replace the appliance base, ensure that the flex cable connecting the PCB-2

Board to the PCB-3 Board is not rubbing against the print roller.

15. If you have no additional repairs to perform, return the SST/HP-4 Transport to the device

cabinet.

16. Restore power to the device.

Figure 6.6

PCB-2 Board

Phillips Screws

Single Track Maghead

Flex Cable Connector
to PCB-3 Board

Summary of Contents for MG-1000



























































































Search results

Summary of Contents for MG-1000

Reviews:

Related manuals for MG-1000

Brands by name

Popular brands

3M MG-1000, Manual

Search results

Summary of Contents for MG-1000

Reviews:

Related manuals for MG-1000

Brands by name

Popular brands