manualshive.com logo in svg

3M Liqui-Cel EXF-10x28 Series, Assembly And Disassembly Instructions, Page: 11 / 12

Share
Download
3M Liqui-Cel EXF-10x28 Series Assembly And Disassembly Instructions Download Page 11

• 

(G)  Turn the vacuum pump on. Press the end caps against the O-rings.

 

• 

 (H)  While the end cap is pulled tight against the housing, place the V-Band 

clamp on the ridge of the housing and the end cap and tighten the 

clamp. Repeat this step for the other end.

 NOTE:

  Using ISO Ashby Cross oil on the nut will help get the nut  

on and off more easily.

• 

Turn off the vacuum. Remove the blind flanges from the shell connections 

and proceed to tighten the center seal.

CENTER SEAL TIGHTENING

• 

(I)  Insert the center seal tool into the center nozzle. Turn the tool until you 

feel the notch in the tool mesh with the nubs of the center nut.

• 

Using a counter clockwise motion, slowly torque the center seal to  

90 ft/lb. (122 Newton/meters). Repeat for other end.

 

PRESSURE TEST

• 

(J)  Bolt blind flanges on both lumen ports and one of the shell ports.

• 

Bolt a flange equipped with a 0-100 psi gauge and hose connection.

• 

Pressurize the housing to 60 psig with clean, oil free, air.

• 

Isolate the pressurized housing and monitor the pressure to verify a leak 

free seal. There should be no pressure decay over 30 minutes.

G

H

I

J

Compressed  

Air Source

11

Summary of Contents for Liqui-Cel EXF-10x28 Series













Reviews:

No comments