3M Dynatel 2220M-C3W-CPLR Operator'S Manual Download Page 28

28

78-9000-0021-3-D

November 2016

This product is in accordance with the requirements of the European  

directive 2014/53/EU .

Electrical Markets Division

6801 River Place Blvd .

Austin, TX 78726-9000

1-800-200-0265

FAX: 1-877-601-1305

www .3M .com/dynatel

Please recycle . Printed in USA © 3M 2016 .  

All rights reserved . 78-9000-0021-3

3M is a trademark of 3M Company . All other trademarks are the property of their respective owners .

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on 

information believed to be reliable, but the accuracy or completeness is not guaranteed . Before using 

this product, you must evaluate it and determine if it is suitable for your intended application . You assume 

all risks and liability associated with such use . Any statements related to the product which are not 

contained in 3M’s current publications, or any contrary statements contained on your purchase order 

shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.

Limited Product Warranty. 

3M Locators (except accessories), will conform to 3M’s published specifications and will be free  

from defects in material and manufacture for a period of twelve (12) months from the date of 

purchase. Dry cell batteries included in any of 3M’s products are warranted only to the extent the 

battery manufacturer determines such batteries are covered by its warranty . Locating accessories are 

warranted for ninety (90) days after purchase. 3M’s obligations and liability under this warranty are 

limited to repairing, replacing or refund of the purchase price, at 3M’s option, any of 3M’s products 

which, after normal and proper usage, are determined by 3M to be defective . This warranty does not 

extend to any of 3M’s products which have been subjected to misuse, neglect, accident or improper 

applications, nor shall it extend to products which have been repaired or substantially altered outside 

3M’s manufacturing or repair facility, nor to any associated instruments, equipment or apparatus. 

Before utilizing any of 3M’s products, BUYER should determine the suitability of the product for 

BUYER'S intended use . 

3M MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING 

ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  

In no case shall 3M be liable for any special, incidental, or consequential damages based upon

breach of warranty, breach of contract, negligence, strict liability or any other legal theory . This 

limitation does not apply to claims for personal injury .

Special Condition:

 Shipments into authorized distributor/supplier locations will have an additional 

ninety (90) day warranty period .

This is the EU symbol for equipment that is covered 
under the Waste from Electrical and Electronic 
Equipment (WEEE) directive per CENELEC 
Specification 5041. It indicates that certain products 
should not be discarded in the trash, but rather 
should be recycled.  This applies to all electronic 
pluggable and battery powered products.

This is the EU symbol for equipment that is covered under the Waste 

from Electrical and Electronic Equipment (WEEE) directive per CENELEC 

Specification 5041. It indicates that certain products should not be 

discarded in the trash, but rather should be recycled . This applies to all 

electronic pluggable and battery powered products .

3M

 Dynatel

 Advanced Pipe/Cable Locator 2220M

Summary of Contents for Dynatel 2220M-C3W-CPLR





























Reviews: