3M DBI-SALA 2100041 User Instructions Download Page 12

I S O

9 0 0 1

FM534873

GLOBAL PRODUCT WARRANTY, LIMITED REMEDY 

AND LIMITATION OF LIABILITY

WARRANTY:

 THE FOLLOWING IS MADE IN LIEU OF ALL WARRANTIES OR CONDITIONS, EXPRESS 

OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR 

FITNESS FOR A PARTICULAR PURPOSE.
Unless otherwise provided by local laws, 3M fall protection products are warranted against factory 

defects in workmanship and materials for a period of one year from the date of installation or fi rst use 

by the original owner.

LIMITED REMEDY:

 Upon written notice to 3M, 3M will repair or replace any product determined by 

3M to have a factory defect in workmanship or materials. 3M reserves the right to require product be 

returned to its facility for evaluation of warranty claims. This warranty does not cover product damage 

due to wear, abuse, misuse, damage in transit, failure to maintain the product or other damage beyond 

3M’s control. 3M will be the sole judge of product condition and warranty options. 
This warranty applies only to the original purchaser and is the only warranty applicable to 3M’s fall 

protection products. Please contact 3M’s customer service department in your region for assistance.

LIMITATION OF LIABILITY:

 TO THE EXTENT PERMITTED BY LOCAL LAWS, 3M IS NOT LIABLE 

FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT 

LIMITED TO LOSS OF PROFITS, IN ANY WAY RELATED TO THE PRODUCTS REGARDLESS OF THE 

LEGAL THEORY ASSERTED.

Distributed by Engineered Fall Protection

[email protected]

www.EngineeredFallProtection.com

Tel:  (314) 492-4422

Summary of Contents for DBI-SALA 2100041













Reviews: