background image

Preface 

This user guide describes the features and functions of the 3M™ AT9000 MK2 Full Page Reader  
(PV60-xx-xx-xx). 

Revision History 

Version 

Date 

Description 

Feb 27, 2013 

Release version 

 

Electromagnetic Compatibility (EMC) 

The Products are designed to be immune to levels of interference generated within an office environment 
and not to interfere with other equipment. In order to provide this level of compatibility the Product, its 
cabling and PSU or its installations, must not be modified in any way. 

 

Modifications or changes to the Product, the interface cables or the power supply 
not expressly approved by the manufacturer could void the User's authority to 
operate the Product and/or break local laws or regulations. 

For further regulatory information or copies of certificates contact your local 3M representative or the 
manufacturer at 

[email protected]

 

 
EMC Compliance Europe 

 

The Product meets the following European Council Directives:  

  Scanner: EMC (2004/108/EC), RFID Option RE&TTE (1999/5/EC) 

  PSU: EMC (2004/108/EC), LVD (2006/95/EC) 

FCC/Canada Radio Frequency Rules and Regulations 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant 
to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications. Operation of this equipment 
in a residential area is likely to cause harmful interference in which case the user will be required to 
correct the interference at his/her own expense. 

NO MODIFICATIONS. Modifications to this device shall not be made without the written consent of 3M 
Company. Unauthorized modifications may void the authority granted under Federal Communications 
Commission Rules permitting the operation of this device. 

 

Copyright 2018   IDScience Inc. Rev. 20180725 

3M™ AT9000 MK2 Full Page Reader User Guide

 

Introduction 

Summary of Contents for AT9000 MK2

































Reviews: