3M 7620-S-2 Page 10 Instructions Manual Download | Manualshive

Page: 10 / 20

background image

10

78-8117-0508-2 Rev D

Shield Wires

Constant Force Spring

Ground Braid

1

ST

Scotch® Mastic Strip 2230

Solder Block

2

ND

Scotch® Mastic Strip 2230

Ground Braid Leg

Trim

Cable

Wire

Shield

Figure 12

8.5 Wrap two highly stretched half-lapped layers of electrical grade vinyl tape around mastic seal, constant force

spring and exposed shield wires (

Figure 13

).

NOTE: Take care not to cover exposed semi-con insulation shield. A minimum of 3/4" (19 mm) must be exposed.
SPECIAL NOTE FOR CLOTH OR PAPER SEMI-CON INSULATED SHIELD: In cables with cloth or paper

semi-conductive shields, it is recommended the shield be over wrapped with one half-lapped layer of highly

stretched semi-conductive rubber tape such as Scotch® Electrical Semi-Conducting Tape 13.

Semi-Con

Constant Force Spring

Two Half-Lapped Layers of Electrical Grade Vinyl Tape

Shield Wires

Scotch® Mastic Strip 2230

Vinyl Tape Marker

1" (25 mm)

Figure 13

«
...
8
9
10
11
12
...
»

Summary of Contents for 7620-S-2





















Reviews:

No comments

Related manuals for 7620-S-2

Brand: Eagle Pages: 2

Brand: Oasis Pages: 3

Brand: SYNCHRO Pages: 24

Brand: Whirlwind Pages: 2

Brand: Metra Electronics Pages: 4

Brand: NEC Pages: 34

Brand: NEC Pages: 10

Brand: NEC Pages: 8

60XM5 - PlasmaSync - 60" Plasma Panel

Brand: NEC Pages: 10

60XP10 - PlasmaSync - 60" Plasma Panel

Brand: NEC Pages: 10

Brand: NEC Pages: 75

Brand: NEC Pages: 10

Brand: NEC Pages: 7

Brand: NEC Pages: 79

Brand: NEC Pages: 3

60XP10 - PlasmaSync - 60" Plasma Panel

Brand: NEC Pages: 44

Brand: NEC Pages: 10

60XP10 - PlasmaSync - 60" Plasma Panel

Brand: NEC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands