background image

4 / 11

MO 0765-0601

V. Wall Mounting

The enclosed 3M Dual Lock™ fastening discs
must be screwed to the wall using the attached
template approximately 1,500mm (5 feet) above
the floor. Drill three holes of 5 mm (0.2 in)
diameter at marked locations. Make sure the area
on the 740 in which the Dual Lock™ fastening
strips are placed is free of dust and dirt. Attach the
3M Dual Lock™ fastening strips to the rear of the
740 tester to the bottom and top in parallel; see
drawing for locations.

For securing on the wall, press the 740 firmly
against the discs. For removal of the 740, lift the
top corners with both hands.

VI. Wrist Strap Test

Put the wrist band on with ground cord attached
and insert the ground cord into the wrist strap
plug-in jack. Depress the metal contact plate and
hold it. One of the indicator LEDs will illuminate.

An illuminated green LED indicates that the wrist
strap performs within the resistance range of 750
k

 to the upper selected value of 2, 5, 10 or 35

M

. If a red "<" LED is illuminated, the current

limiting resistor in the ground cord is bypassed
and the cord has to be replaced. The red ">" LED
indicates that the selected resistance range is
exceeded. Check to see if the high resistance is in
the cord, the wrist band or in the contact between
wrist band and the operator's skin. To check the
resistance of the ground cord, leave the plug end
of the ground cord attached to the tester and
disconnect the snap end from the wrist band.
Connect ground cord snap to the stud in the hand
symbol or press it onto the contact plate and
depress the plate until one of the LEDs is
illuminated.

If the green LED illuminates
now, the ground cord can be
used.

If the red ">" LED is
illuminated, replace the
ground cord.

In some cases, high contact resistance between the
skin and wrist band will cause the tester to show a
red ">" LED condition. This resistance may be
caused by dry skin or the presence of hair in the
wrist area. The use of a skin lotion is
recommended to solve this problem. If a red ">"
LED condition still exists, replace the wrist band.

Note: The use of skin lotions are not
recommended for use with the 3M™ 4600 Series
Thermoplastic Wrist Bands.

Rear of the 740

Template

5 feet

(1 500 mm)

Summary of Contents for 740













Reviews: