3M 6832-50/OM2-JG1 MM Instructions Manual Download Page 15 | Manualshive

Page: 15 / 15

3M 6832-50/OM2-JG1 MM Instructions Manual Download Page 15

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be relia-
ble, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suit-
able for your intended application. You assume all risks and liability associated with such use. Any statements related to the prod-
uct which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have

3

Communication Markets Division
3M Telecommunications

www.3M.com/Telecom

©3M 2016. All rights reserved.

Warranty; Limited Remedy; Limited Liability.

This product will be free from defects in material and manufacture for a period of 12 months from the time of purchase.

3M MAKES

NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FIT-
NESS FOR A PARTICULAR PURPOSE

. If this product is defective within the warranty period stated above, your exclusive

remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.

Except where

prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether indirect, special,

3M is a trademark of 3M Company

«
...
13
14
15

Summary of Contents for 6832-50/OM2-JG1 MM
















Reviews:

No comments