Fitting Instructions
Before assigning any respirator to be worn in a contaminated
area, we recommend that a qualitative or quantitative fit check
be performed before entering the workplace.
Fitting instructions must be followed each time the respirator is worn.
Place the respirator over the mouth and nose, then pull the
1.
harness over the crown of the head.
Take the bottom straps in both hands, place them at the back
2.
of the neck and hook them together.
Tighten the top straps first by pulling on ends to achieve a
3.
comfortable and secure fit.
Tighten bottom straps using either front or rear adjustments.
4.
(Strap tension may be decreased by pushing out on back side
of buckles).
Fit Check
Perform a positive and/or negative pressure fit check each time
the respirator is donned.
Positive pressure Face Fit check (all Filters except 3M™
6035, 6038 / 2000 Series Filters).
Place the palm of the hand over the exhalation valve cover
1.
and exhale gently.
If the respirator bulges slightly and no air leakage between
2.
the face and the respirator is detected, a proper fit has been
achieved.
If air leakage is detected, reposition the respirator on the
3.
face and/or readjust the tension of the strap to eliminate the
leakage.
Repeat the above face fit check.
4.
If you cannot achieve a proper fit, do not enter the
5.
contaminated area. See your supervisor.
Negative pressure face fit check (3M™ 6035, 6038 / 2000
Series Filters)
Push the filter cover down (6035, 6038) or press your thumbs
1.
into the central indentation of the filters (2000 series), inhale
gently and hold your breath for five or ten seconds.
If the respirator collapses slightly, a proper fit has been
2.
achieved.
If air leakage is detected, reposition the respirator on the
3.
face and/or readjust the tension of the straps to eliminate the
leakage.
Repeat the above face fit check.
4.
If you cannot achieve a proper fit, do not enter the
5.
contaminated area. See your supervisor.
Materials
PART
MATERIAL
Face Mask
Thermoplastic Elastomer
Head Harness
Polyethylene
Head Strap
Polyester / cotton / Polyisoprene
Inhalation Valve
Polyisoprene
Exhalation Valve
Silicone Rubber
Gasket
Silicone Rubber
6000 Filter Body
Polystryrene
6000 Filter Element
Activated / Treated Carbon
5000 / 2000 Series Filter material
Polypropylene
Please recycle.
© 3M 2010. All rights reserved.
3M a/s
Sikkerhedsprodukter
Fabriksparken 15
DK-2600 Glostrup
Telefon: 43 48 01 00
Fax: 43 96 85 96
E-mail: [email protected]
www.3Msikkerhed.dk
Important Notice
3M does not accept liability of any kind, be it direct or consequential (including, but not limited to, loss of profits, business and/or goodwill)
arising from reliance upon any information herein provided by 3M. The user is responsible for determining the suitability of the products
for their intended use. Nothing in this statement will be deemed to exclude or restrict 3M’s liability for death or personal injury arising from
its negligence.
Spare parts
PART
MATERIAL
6895
Inhalation Gasket
501
Retainer for 5000 Series Filters
603
Particulate Filter Platform
105
Face Seal Cleaner
S-200
Supplied Air Regulator
106
Half Mask Carry Case
Respiratory Protection is only effective if it is correctly
selected, fitted and worn throughout the time when the
wearer is exposed to respiratory contaminants.
3M offers advice on the selection of products, and training in the
correct fitting and usage.
For more information on 3M products and services please
call the 3M Health & Safety Helpline.
DS6
5/
000
12
5-
1
