background image

3M is a registered trademark of 3M. UniShield

®

is a registered trademark of BICC Cables.

Note: The core material being removed from the Cold Shrink Tube is mixed polymers and can be recycled with other waste.

IMPORTANT NOTICE

Before using this product, you must evaluate it and determine if it is suitable for your intended application.  You assume all risks and liability
associated with such use.

Warranty; Limited Remedy; Limited Liability.   

This product will be free from defects in material and manufacture as of the date of

purchase.  

3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

If this product is defective within the warranty period stated above,

your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.  

Except

where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special,
incidental or consequential regardless of the legal theory asserted.

Electrical Products Division

6801 River Place Blvd.
Austin, TX 78726-9000
800/245-3573

Printed on 50% recycled paper

Litho in USA

www.3M.com/elpd

with 10% post-consumer

©3M 1999 

78-8124-4544-9-B

Summary of Contents for 5811 Series













Reviews: