34
Special Set-Up Procedure
(Continued)
4.Lift the lower taping head as shown in Figure 6-2
and remove it from the machine bed.
Outer Column Re-Positioning
Refer to Figure 6-3
Moving the outer columns up one set of mounting
holes increases the maximum box size handled by
the case sealer from 510 mm [20 inch] to 615 mm
[24.25 inch].
To move the outer columns up one set of mounting
holes:
1.Crank side drive belts to full open position.
2.Crank upper assembly up approximately
510 mm [20 inch] from machine bed.
3.Place solid blocks approximately 485 mm
[19 inch] high beneath upper assembly at front
and rear.
Figure 6-2 Remove Lower Taping Head
5.Remove and retain four mounting screws in
each outer column.
WARNING A second person
should assist with this part of set-
up to hold (steady) upper assembly until
columns are re-positioned and column
screws are installed and tightened.
6.Crank outer columns up 100 mm [4 inch].
Check to see that upper head is aligned
horizontally with the bed of the machine.
Re-install four screws in each column.
7.Crank upper assembly up and remove blocks.
CAUTION Holding taping head
in another way may increase the
danger of being injured by the tape cut-
off knife.
5.Refer to Section
II
, "Adjustments Changing
Tape Leg Length", page 13 for taping head
set-up.
6.Replace taping heads reverse of disassembly.
Note
The one-way tension roller position is
adjustable to control the leading tape leg
length. Refer to Section
II
, "Adjustments
Leading Tape Leg Length, page 13.
4.Crank upper assembly down until upper
assembly touches blocks at front and rear.
Important Shim blocks as necessary to
keep upper assembly parallel with machine
bed.
Summary of Contents for 3M Matic 120af
