3M 3M-30 Install Manual Download

Page: 14 / 18

W Y RH G

WIRES

4 Wire Heat/Cool

STEP 1 - Connect the W wire to the W terminal. This connects the heat.

STEP 2 - Connect the Y wire to the Y terminal. This connects the cooling compressor.

STEP 3 - Connect the RH or R wire to the RH terminal. This connects the power.

STEP 4 - Connect the G wire to the G terminal on the thermostat. This connects the fan.

STEP 5 - Set HVAC selection switches to NORMAL and:

If you have gas or oil heat, set the HEAT TYPE switch to GAS.

If you have electric heat, set the HEAT TYPE switch to ELEC.

Your HVAC system is now connected to the 3M-30.

Please Go To Page 6

W Y RH RC G

WIRES

5 Wire Heat/Cool

STEP 1 - Connect the W wire to the W terminal. This connects the heat.

STEP 2 - Connect the Y wire to the Y terminal. This connects the cooling compressor.

STEP 3 - Disconnect the jumper between RH and RC terminals.

STEP 4 - Connect the RH wire to the RH and the RC wire to the RC terminals. This connects power.

STEP 5 - Connect the G wire to the G terminal. This connects the fan.

STEP 6 - Set HVAC selection switches to NORMAL and:

If you have gas or oil heat, set the HEAT TYPE to GAS.

If you have electric heat, set the HEAT TYPE to ELEC.

Your HVAC system is now connected to the 3M-30.

Please Go To Page 6

Thermostat

Terminals

HVAC SYSTEM

REMOTE POWER

C H B O

Y Y

RH RC G A

RH RC

HVAC SYSTEM

REMOTE POWER

C H B O

Y Y

RH RC G A

Thermostat

Terminals

Summary of Contents for 3M-30



















Search results

Summary of Contents for 3M-30

Reviews:

Related manuals for 3M-30

Brands by name

Popular brands

3M 3M-30, Install Manual

Search results

Summary of Contents for 3M-30

Reviews:

Related manuals for 3M-30

Brands by name

Popular brands