manualshive.com logo in svg

3DLabPrint Zivko EDGE 540v3, User Manual

Share
Download
3DLabPrint Zivko EDGE 540v3 User Manual Download Page 33

page

 33

... print your plane  | www.

3DLabPrint

.com

5. Servo installation

Our EDGE 73“ was designed for 4pcs of standard size servos (approx. 40x38x20mm). 

5.1 Elevator and Rudder

Instal all servos (use any hot wire) then install rudder, elevator and pull pull servo system.

NOTE: apply Loctite thread locker 243 (blue) to all bolts thread - this is very important if you 
don‘t want to lose your plane.

Proceed the way shown in videoguide:

  

See video guide #5.1

You will need:         2x standard size servo
                                       1.5/12mm self tapping screws
                                       any fire source and wire 1-1.5mm (hot wire)
                                  2x pull-pull rudder and elevator system or similar
                                        8x (treaded brass wire end 2mm+crimp tube, 6 m wire 0.5-0.8mm)
                                       pliers

High rates servo arms:

Low rates servo arms:

Summary of Contents for Zivko EDGE 540v3
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands