3DHISTECH PANNORAMIC SCAN RX 1.1 User Manual Download | Manualshive

Page: 153 / 165

background image

PANNORAMIC® SCAN RX 1.1

TROUBLESHOOTING AND MAINTENANCE

NOVEMBER 18, 2021

152

FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.

•

Lumencor SOLA U-NIR is switched off.

•

Switch light source on, otherwise contact 3DHISTECH Service for support.

9.5

Maintenance

This chapter describes the most common maintenance solutions that can be performed by the
user of the product. For maintenance solutions not described in this manual, contact the service
personnel.

9.5.1

Removing the protective covers

The protective covers of the Pannoramic® SCAN RX must be opened to perform any
maintenance work, and also to eliminate errors, for example slide or magazine jamming.

Before removing the covers, exit Pannoramic® Scanner Software for Research control
software, switch off the 24 V power supply and disconnect the power cables.

Warning!

Avoid leaning over the device when opening it.

Figure 130. Removal of covers

Five eccentric screws

(3)

are located on the bottom face of the base plate

(4)

. They attach

the covers to the base plate.

«
...
151
152
153
154
155
...
»

Summary of Contents for PANNORAMIC SCAN RX 1.1






































































































































































Reviews:

No comments

Related manuals for PANNORAMIC SCAN RX 1.1

Brand: kaarta Pages: 2

Brand: Magtek Pages: 47

FLATSCAN REV PZ

Brand: LZR Pages: 12

Brand: Patriot Pages: 8

Brand: Uniden Pages: 61

Brand: Network Security Pages: 64

Brand: IFM Pages: 13

Brand: GTCO CalComp Pages: 1

ScanPlus 7 ATF1824C

Brand: GTCO CalComp Pages: 2

Brand: Bell and Howell Pages: 1

UNITEST Wallscanner

Brand: BEHA Pages: 32

Brand: polyga Pages: 5

Pannoramic SCAN II 2.0

Brand: 3DHISTECH Ltd. Pages: 142

Kiosk ePassport Reader PV35-02 Series

Brand: 3M Pages: 36

Scantrak RP-6120

Brand: RCA Pages: 2

Brand: Xerox Pages: 2

Brand: Radio Shack Pages: 3

Brand: Youjie Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands