3D AEROWORKS VOUGHT F4U-1D CORSAIR Assembly Manual And User Manual Download | Manualshive

Page: 9 / 24

background image

8

Place a drop of CA in the hinge slot of the control surface and insert the hinge. Be sure that
the hinge is perpendicular to the control surface. Then bend the hinges to 90deg back and
forward a few times to make sure they are appropriately loose. (the outer aileron and
elevator hinge may need to be trimmed).

See below

9

Fit the horizontal stabilisers to the fuselage using small sections of 3mm bbq skewers to align
the stabilises and glue with CA.

«
...
7
8
9
10
11
...
»

Summary of Contents for VOUGHT F4U-1D CORSAIR

























Reviews:

No comments

Related manuals for VOUGHT F4U-1D CORSAIR

Brand: HYPE Pages: 24

Brand: Flexifoil Pages: 28

Brand: Jabiru Pages: 64

Brand: Ocean Rodeo Pages: 16

Brand: Schempp-Hirth Pages: 73

Ventus-3T Sport

Brand: Schempp-Hirth Flugzeugbau Pages: 177

Brand: GREAT PLANES Pages: 20

Brand: GREAT PLANES Pages: 28

EV-97? EUROSTAR ?model 2000 version R

Brand: EVEKTOR-AEROTECHNIK Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands