3Com VCX V7000 Maintenance Manual Download

Page: 337 / 344

CLI Command Descriptions

337

> conf cct row=4 index=1 trustedaddr=<IP address>

You can enter the

help

command at the remote CLI application prompt

(

> help

) to display a list of application commands. You can enter a

command without a parameter to display a list of available parameters,
for example:

> show

AcctCfg

AcctLogFilters

AcctServer

AcctServerStats

AcctServiceStats

AdhocServer

AppCmd

AppId

AppMibs

AuthCfg

AuthLogFilters

AuthServer

AuthServerStats

AuthServiceStats

CcCfg

CcLogFilters

CcQosCfg

CcQosMonitoredEndpoints

CcStats

CcTrusted

LogCfg

SipCfg

SipLogFilters

CLI Command
Descriptions

The remote CLI application uses the following commands for
administering the Call Processor:

Table 21

Remote CLI Command Descriptions

Command

Description

exit

Quits the Remote CLI application.

shutdown

Shuts down the Call Processor gracefully.

version

Shows the software version of the Call Processor and the version of
the Distributed Message Routing (DMR) 3Com proprietary protocol.

Summary of Contents for VCX V7000

























































































































































































































































































































































Search results

Summary of Contents for VCX V7000

Reviews:

Related manuals for VCX V7000

Brands by name

Popular brands

3Com VCX V7000, Maintenance Manual

Search results

Summary of Contents for VCX V7000

Reviews:

Related manuals for VCX V7000

Brands by name

Popular brands