manualshive.com logo in svg

3Com VCX V7000, Installation Manual

Share
Download
3Com VCX V7000 Installation Manual Download Page 443

Replacing a Disk (Regional Office)

441

Replacing a Disk 
(Regional Office)

Use the procedures in this section to replace a disk on one of the servers 
at a regional office.

■

Replacing an IP Telephony and Messaging Disk

■

Replacing a Call Processing Server Disk

■

Replacing an IP Messaging Disk

■

Replacing an Authentication and Directory Server Disk

■

Replacing a Call Records Server Disk

■

Replacing a Disk (Branch Office)

■

Replacing a Disk on an IP Telephony and Messaging Server

■

Replacing a Disk on an IP Telephony Server

Replacing an

IP Telephony and

Messaging Disk

In each regional office that has no associated branch offices there are two 
IP Telephony and Messaging Servers. To replace a failed disk on one of the 
servers, see 

“Replacing a Disk (Single Site)”

 earlier in this chapter.

Replacing a Call

Processing Server

Disk

In each regional office, there are two Call Processing Servers. To replace 
the disk in either the Primary Call Processing Server or the Secondary Call 
Processing Server, follow the instructions in this section.

If this server is configured for RAID operation, see 

“RAID Disk Failure”

, 

earlier in this appendix.

1

Replace the failed disk.

a

Remove power from the down server.

b

Remove the failed disk.

c

Install the replacement disk.

d

Apply power to the server.

e

Press the start button on the front panel.

2

Log in as 

root

 and configure the networking parameters on the down 

server using this command:

vcx-config-network --wizard

If the down server is the Primary IP Telephony Server, follow the 
instructions in 

“Configuring a Primary Call Processing Server”

 in 

Chapter 5

.

Summary of Contents for VCX V7000









































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands