3Com 3CR17660-91 Configuration Manual Download | Manualshive

Page: 70 / 422

background image

56

C

HAPTER

12: V

OICE

VLAN C

ONFIGURATION

As multiple types of IP phones exist, you need to match port mode with types of voice
stream sent by IP phones, as listed in Table 37.

CAUTION:

If the voice stream transmitted by an IP phone is tagged and the port

which the IP phone is attached to is 802.1x-enabled, assign different VLAN IDs for the
voice VLAN, the default VLAN of the port, and the 802.1x guest VLAN to ensure the
two functions to operate properly.

If the voice stream transmitted by the IP phone is untagged, the default VLAN of the

port which the IP phone is attached can only be configured as a voice VLAN for the
voice VLAN function to take effect. In this case, 802.1x authentication is unavailable.

Table 37

Port modes and voice stream types

Port voice
VLAN mode

Voice stream
type

Port type Supported or not

Automatic
mode

Tagged voice
stream

Access

Not supported

Trunk

Supported

Make sure the default VLAN of the port exists
and is not a voice VLAN. And the access port
permits the packets of the default VLAN.

Hybrid

Supported

Make sure the default VLAN of the port exists
and is in the list of the tagged VLANs whose
packets are permitted by the access port.

Untagged voice
stream

Access

Not supported, because the default VLAN of
the port must be a voice VLAN and the access
port is in the voice VLAN. To do so, you can
also add the port to the voice VLAN manually.

Trunk

Hybrid

Manual mode

Tagged voice
stream

Access

Not supported

Trunk

Supported

Make sure the default VLAN of the port exists
and is not a voice VLAN. And the access port
permits the packets of the default VLAN.

Hybrid

Supported

Make sure the default VLAN of the port exists
and is in the list of the tagged VLANs whose
packets are permitted by the access port.

Untagged voice
stream

Access

Supported

Make sure the default VLAN of the port is a
voice VLAN.

Trunk

Supported

Make sure the default VLAN of the port is a
voice VLAN and the port permits the packets of
the VLAN.

Hybrid

Supported

Make sure the default VLAN of the port is a
voice VLAN and is in the list of untagged VLANs
whose packets are permitted by the port.

«
...
68
69
70
71
72
...
»

Summary of Contents for 3CR17660-91







































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3CR17660-91

Brand: Cabletron Systems Pages: 88

Brand: IBM Pages: 2

Brand: WAGO Pages: 39

Brand: Manhattan Pages: 2

Brand: Hall Technologies Pages: 35

Brand: CYP Pages: 32

2X2 VGA SWITCHER

Brand: Gefen Pages: 12

Brand: Grozone Control Pages: 20

SIL IntelliPoint RF S*R*L Series

Brand: Ametek Pages: 93

INTEGRA KLI 310

Brand: Velux Pages: 9

Custom Pro Matrix

Brand: Bluestream Pages: 27

Brand: Omron Pages: 4

Brand: GeoVision Pages: 7

Brand: S&S Northern Pages: 8

Brand: N-Tron Pages: 15

AVlink VAX-8404F

Brand: C&C TECHNIC Pages: 2

Brand: Omron Pages: 4

Brand: Good Way Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands