3ality 3FLEX TS-5-Compact User Manual Download Page 15 | Manualshive

Page: 15 / 26

background image

TS-5 Compact BeamSplitter User Manual
Version 1.0 – September 2011

15

4 Preparing the Stereo Camera Platform

4.1 Camera/Lens sled assembly

1.

Disconnect platform power.

2.

Remove camera sled from camera platform by loosening the knob above the height/pitch bracket.

3.

Carefully pulling the spring-loaded safety-lock knob, remove the sled from the platform. (The knob is
designed to catch in each of the camera platform’s grooves).
Take care not to force anything.

Figure 5.

Right eye camera assembly

Mounting Knob

Spring-loaded
safety-lock
knob

«
...
13
14
15
16
17
...
»

Summary of Contents for 3FLEX TS-5-Compact



























Reviews:

No comments

Related manuals for 3FLEX TS-5-Compact

Brand: NEC Pages: 144

Brand: Samsung Pages: 7

Brand: Banner Pages: 2

Brand: Gainsborough Pages: 2

Alerts TX60U-IT

Brand: La Crosse Technology Pages: 3

Brand: Okina USA Pages: 3

XMODS Custom RC

Brand: Radio Shack Pages: 4

Brand: Saab Pages: 10

Brand: S/C Black Pages: 34

AERASGARD RCO2-W

Brand: S+S Regeltechnik Pages: 7

Brand: YachtSafe Pages: 2

Brand: iArmor Pages: 6

Brand: Yakima Pages: 21

Brand: Profoto Pages: 12

Honeywell RE210P

Brand: Resolution Pages: 4

Brand: Kreg Pages: 36

autoSteady AS101

Brand: Enduro Pages: 48

Brand: hepco & becker Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands