Component
(구성품)
①
Model :
EV2
②
Power :
AC 100~120V, 50~60Hz
AC 220~240V, 50~60HZ
③
Power Consumption :
1250W
(Heater:550W Motor:1250W)
④
Dimension :
180 × 250 × 320
㎜
⑤
Weight :
8kg
①
Model :
EV-03
②
Power :
AC 100~120V, 50~60Hz
AC 220~240V, 50~60HZ
③
Power Consumption :
550W
(Heater:550W Pump:50W)
④
Dimension :
180 × 250 × 320
㎜
⑤
Weight :
8kg
Specification
04
A. Preparation before use
①
Select the sheet that best suits your purpose. (Temporary, Splint, retainer, bleaching, and so on)
②
After connecting the power, check that the heater
and motor are working properly.
(Timer
8
: Turn clockwise to operate, 3-switch
: Press
I
-> Heater lamp
on, Press
II
-> Sound)
B. How to use
①
Hold the upper frame handle
and turn it 180° counterclockwise to face backward.
②
Turn the timer
8
clockwise and then press the 3-switch
I
.
(At this time, the heater lamp
is turned on and the heater
is heated. The warm-up time is about
2 minutes and 30 seconds, and the condition may vary depending on the environment.)
③
Place the model in the center of the hole plate
6
.
④
Using the sliding handle
2
, lift up to the top of the hexagonal post
.
⑤
Turn the release handle
5
clockwise to release the lock and lift it up.
⑥
Place the sheet you want to use on the lower sliding
4
, lower the upper sliding
3
and turn the release
handle
5
counterclockwise to fix it with the lower sliding
3
. (Only for square 127x127mm)
⑦
Hold the upper frame handle
and turn it 180° clockwise to face the upper frame
1
forward.
(Do not touch the heated upper frame
1
with your hand)
⑧
When the fixed sheet is lowered to the height of the model or about 1/2, turn the upper frame handle
180° counterclockwise to face the upper frame
1
backward.
⑨
After press 3-switch
II
, hold the sliding handle
2
and lower the sliding down until it is completely in
contact with the main frame
7
.
(At this time, the heater
is turned off and the motor is operated.)
⑩
Wait until the sheet is fully formed in the model, then turn off the 3-switch
II
.
(About 10 to 60 seconds).
⑪
Wait until the sheet cools down (about 1 to 3 minutes), then turn the release handle
5
clockwise to
take out the molded sheet.
C. Management and storage methods
①
Disconnect the power cable from the outlet
②
After using, please make sure that the equipment is clean.
③
Do not place heavy objects on the upper frame.
④
Do not store this machine in a humid place.
Operation
05
①
There is a risk of burns because the heater area is heated after using this product.
②
Do not disassemble or repair this product.
③
After using this product, must remove the power cable from outlet
④
Contact with sheet softening may cause sheet deformation and burns.
⑤
Do not use for other purposes.
Caution
06
①
Please keep out of reach of children.
②
Please use in a place separated from fire and water.
③
Temperature :
-10 ~ 70
℃
④
Humidity :
10~100%
⑤
Pressure :
50~106kpa
Maintenance & Storage
07
This product has passed strict testing and inspection.
This product is warranted for 12 months from the date of purchase from us.
①
This product will be repaired free of charge the performance and function defect that occurred under normal use
condition within the warranty period. If it cannot be repaired, we will replace it free for charge with a new product.
②
Repair fee will be charged after the warranty period is expired.
③
In case of any of the following cases within the warranty period, repair fee will be charged.
•
Failure caused by intention or negligence of the consumer.
•
Failure caused by repair at a place not designated by us.
•
Failure caused by power supply or faulty connecting devise.
•
Other arbitrary disassembly, failure due to arbitrary alteration, etc.
Warrantee
08
Clean the product and each part with a soft cloth and air.
Cleaning
09
Please contact us if you have any mechanical problems.
•
Telephone :
82-31-909-8774
•
Fax
:
82-31-909-8773
•
Homepage :
www.3amedes.co.kr
Customer Support Division
10
