manualshive.com logo in svg

360 Systems TSS MINI 2100, Operation Manual

Share
Download
360 Systems TSS MINI 2100 Operation Manual Download Page 107

 

TSS MINI Operations Manual 

Page 107 

Gigabit Ethernet Indicators 

 

The Gigabit Network Port card has the following indicator lights: 

 Label 

Indication 

Meaning 

ACT/LNK 

(Left) 

 

Green on 

The port is connected to a valid link partner 

Green flashing 

Data activity 

Off 

No link 

10=OFF 

100=GREEN 

1000=YELLOW 

(Right) 

Off 

10 Mb/sec 

Green 

100 Mb/sec 

Yellow 

1000 Mb/sec 

 

Access To Components 

 

 

Be certain to shut down the server and disconnect the power cord before 

opening the unit for service. 

 

The following sections provide instruction on disassembly and re-assembly for maintenance. 

Opening the Front Panel 

The front panel is easily opened for access to the disk drives bays and front power button. 

Firmly gripping the left and right sides of the panel, pull one side straight out releasing the 

panel from the server. 
To re-install the front panel, verify that all drive bays are completely closed and locked, then 

place the left or right side of the front panel into position pushing firmly on the opposite 

side.  The panel should click into position. 

Removing the Top Cover 

 

Use a No. 2 Philips head screwdriver to remove the one (1) screw toward the rear of the top 

cover.  Then press the two round latches in the top center at the same time and pull or push 

the top cover toward the rear of the server to disengage the latches.  Lift the top cover up 

and away from the server. 

Summary of Contents for TSS MINI 2100














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands