background image

2

3

1. BEFORE STARTING

The following symbols in the manual serve for better guidance. The following table describes the symbols and their meaning.

Before installing the unit, read carefully the section on the safe operation of the heat recovery unit. You will 

find instructions on the safe an proper use of the product.

Symbol

Meaning

ATTENTION!
PLEASE NOTE!
YOU WILL NEED

TECHNICAL INFORMATION

Warning or Caution

Important instructions
Practical tips and information

Reference to a different part of the 

manual

Detailed technical information

This manual provides instructions on how to properly install the unit. Before installing the unit, read carefully the entire manual. 

The manufacturer reserves the right to make changes, including in the technical documentation, without prior notice. Keep the 

manual in a safe place for future reference. The manual is an integral part of the product.

Declaration of conformity 

The product has been designed, produced an marketed in compliance with all the applicable provisions, and abides to the pro-

visions of the European Parliament and Council, including the amendments under which it has been classified. It is safe under 

normal conditions and under the conditions laid down by the manual.  The assessment was conducted pursuant to harmonized 

European standards included in the relevant EC Declaration of Conformity. The current and full version of the EC Declaration of 

Conformity can be found at www.2vv.cz or in the enclosed CD.

Summary of Contents for DAPHNE Comfort


























Reviews: