2T Technology HV ANSI Series Technical Reference Manual Download

Page: 31 / 81

HV ANSI Series Technical Reference Manual, MAN0340, Rev. A

4-3

For each subsequent character, press

before entering the numbers.

You can find a list of available ASCII characters with Hex and Decimal equivalents in

Appendix B

If you mistype a character or number, press

to backspace.

10.

To quit without saving, press

11.

To program another key, press

12.

To save the function key programming on 30-key and 40-key terminals, press

. To save the

function key programming on 20-key terminals, press

When saving your changes, the terminal will display:

Warning!

not

remove power from the terminal while the above message appears on the

screen or you will corrupt

all

stored data. Should you remove power during this time, you will have

load default values

Notes

: You can disable function key programming by simultaneously pressing

CTRL

SHIFT

and

while applying power. Refer to the

Restricting Access

procedure for additional information.

To display the results of key programming on your terminal, you must enable ECHO. When

programming a combination of keys that use both modifier keys (such as

CTRL

and

SHIFT

), you

should enable the Shift Lock parameter to avoid conflicts with existing functions (such as

CTRL

SHIFT

and

accesses the Parameter menu) as well as prevent Phantom Key syndrome.

Extended Key Functionality

Note

: Before attempting to program keys with extended functionality, you must enable the Break

Command parameter by using either the

Parameter Setup menu

o r

ANSI Host Commands

Extended Key commands are special hex codes that you use while defining key output to control the

transmission and display of characters on both the terminal side and host side. For example, sending

the string “START” to the host, while displaying “RUNNING” on the terminal. Extended Key

commands fall into the following categories:

•

Break Commands

•

Output Control Commands

•

Pause Commands

•

Branching Commands

•

Handshake-Out Line Manipulation Commands

Break Commands

When a communication line is idle, the normal state of the terminal, the line is

marking

or transmitting

continuous series of ones. The marking signal is a voltage between -3 and -30 VDC. Break commands

place the transmit line into a condition known as

spacing

, where the terminal is sending zeroes for a

specified time (either 250 ms or 3.5 seconds). The spacing signal is a voltage b3 and +30 VDC.

Short Break

When defining key output, enter

as the two HEX digits to specify a break of 250 ms.

Summary of Contents for HV ANSI Series


















































































Search results

Summary of Contents for HV ANSI Series

Reviews:

Related manuals for HV ANSI Series

Brands by name

Popular brands

2T Technology HV ANSI Series, Technical Reference Manual

Search results

Summary of Contents for HV ANSI Series

Reviews:

Related manuals for HV ANSI Series

Brands by name

Popular brands