background image

2N - VoiceBlue Lite 

2.5. Antenna Connection 

The VoiceBlue Lite gateway has one SMA antenna connector for 
all GSM modules, see Fig. 9. An external antenna cable is 
connected to this connector. The external antenna should be 
installed vertically on a place with a good GSM signal. For the 
technical parameters of the antenna refer to Section 12. 

 

Fig. 9 – Antenna Connection 

Tighten the antenna connector gently with your hand, never use a 
wrench! 

2.6. Gateway Power Supply 

 

Be sure to use only the mains supply adapter that is included in 
the gateway delivery. 

 

Before plugging in the gateway, make sure that the mains 
voltage value meets the data given on the mains adapter label. 

 

Make sure that the antenna has been connected. 

If you connect 

the gateway to the power supply without an antenna, the 
GSM module transmitter might get damaged. 

 

Now plug the supply adapter into a wall socket and after it 
connect the adapter connector to the gateway, see Fig. 10. The 
status indicators indicate the proper operation. For their 
meanings refer to Subs. 2.9. 

15

 

VoIPon   www.voipon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299

Summary of Contents for VoiceBlue Lite








































































































































Reviews: