background image

2N® EasyGate IP User Manual

10

 /  

94

DIN Rail Mounting

No other tool is needed for DIN rail installation. The DIN rail bracket has a standard size of 35 
mm. Put the upper inner side of the bracket profile on the DIN rail and push its bottom side to 

make the bracket click and fit to the DIN rail. 

Now all you have to do is slide 

2N

®

 EasyGate IP

from the top into the bracket profile (A) and fit its position with a screw (B).

Wall Installation

Use the bracket and two dowels with screws included in the package to install 

2N

®

 EasyGate IP

on a wall. Drill holes in a selected place and selected height of the wall and insert the dowels. 
Pass the screws through the bracket holes and screw them into the dowels in the wall. Now all 
you have to do is slide 

2N

®

 EasyGate IP

 from the top into the bracket profile (A) and fit its 

position with a screw (B).

2.3 Electric Installation

2N

®

 EasyGate IP

 consists of a VoIP gateway in a black case, removable antenna and phone / PC / 

power supply connecting cables.

To put 

2N

®

 

EasyGate IP

 in operation, connect the device to the power supply, connect an 

external antenna and insert the SIM card.

Device Connection to Power

Connect the supplied power terminals to the POWER connector, connect the power supply to 
the mains.

 The device activity is signaled by status LED indicators. Refer to 

Subsection 2.5 

Overview of LED Indicators

 for details. 

2N

®

 EasyGate IP 

is fed with 9–30 V / 1 A DC. 

Where a 

source other than the included power supply is used, the allowed voltage range and polarity 
have to be maintained according to the technical parameters.

In the case of a power failure, four NiMH size AA (1.2 V / 2000 mAH) batteries inside the device 
provide power backup and thus normal operation of the device. As part of the device, this 
battery pack is placed on the bracket bottom side and covered with a plate fitted with a screw. 
The cell polarity is indicated next to the battery pack space.

Summary of Contents for EasyGate IP































































































Reviews: