background image

7

For your safety and protection, ensure correct placement and angle of ladder. See diagrams 

below. Recommended ladder placement is a 4:1 ratio or approx. 70° to 75°.

NOTE: 

Under no circumstances should anyone be inside the roof top tent if the ladder is 

not locked and secured at the correct angle.

The ladder may need to be adjusted to achieve the correct angle depending on the height of your 

setup. If shortening is required, the adjustment must be done from the top.

Ensure the ladder is fully extended and all rungs are locked in place. Press the first set of locking  

buttons (second rung from the top) and allow the ladder to compress until a gap of approx. 85mm 

is achieved between rung 1 & 2. 

Note:

 The ladder will only lock in the downward position.

Swing in the bottom of the ladder until it supports the weight of the roof top tent. If the angle of the 

ladder is between 70° and 75°, the adjustment is complete. 

Ladder adjustment

NOTE:

 When height adjusted, the ladder will only lock in the downward position.

If further adjustment is required, repeat the above steps by continuing the sequence by depressing 

the next set of locking buttons.

If further shortening is required press the second set of locking buttons (third rung from the top). 

This will close the 85mm gap until rung 1 & 2 are now touching. Swing in the bottom of the ladder 

until it supports the weight of the roof top tent. If the angle of the ladder is between 70° and 75°, 

this adjustment is complete.

TM

SABER USER MANUAL

Summary of Contents for SABER













Reviews: