10 Bar 400D User Manual Download Page 7

7

dropped, it is essential you do not use the housing for diving. Please return the housing immediately for service. 

Please put a note inside to indicate the nature of the accident, so that the severity can be assessed.

6

. Service

To ensure the continued performance of your housing, it should be serviced every year, or after 

every 200 dives. Please note the terms for servicing the housing posted at our website. A full service will 
include:

Inspection of all components for wears or damage (report if repair necessary)

Cleaning of all sealing surfaces, and replacement of all O-ring seals.
Hydrostatic pressure test to 10 Bar.

Note: the replacement of damaged components (except replacement O-rings) may require 

additional cost.

7

. Warranty

The warranty is valid within two years from the date of first purchase. The warranty 

applies only to the housing itself. 10 BAR does not accept any liability either implicit or otherwise 
for any equipment housed inside, or used together with the housing. In the event of the housing 
flooding within the period of warranty, 10 BAR will repair or replace the housing. Please note 
that disassembly of the housing will invalidate warranty. Please fill in the information below, and 

return a copy to 10 Bar Underwater Housing at the address below, to validate the warranty.

Housing Type :
Date of Purchase :
Serial Number :

(Labeled inside housing)

Dealer :
Owner

¡

s Name :

e-mail :
Address:
Tel :
Fax :

Office & Showroom:

Unit C, 2/F., Wing Hin Factory Building, 31-33 Ng Fong St.,

San Po Kong, Hong Kong.

Tel: (852) 2573 3228 Fax: (852) 2811 9180.

Email: 

[email protected] 

Web site: http//www. 10bar.com

Please keep this document for future reference

(Note: due to continuous improvement the latest model housing may differ slightly form those described in this document)

(Copy to be returned to 10 Bar Underwater Housings)

Summary of Contents for 400D








Reviews: