1 Sound Contour CT212 Manual Download Page 4

Chapter 2. Accessories

Contour CT212 Rigging System

Angle-adjustable mount for pole or flown deployment

Figure  3. The Contour Rigging System

This adjustable rigging system attaches to the top or bottom of the CT28 
and allows for various rigging options such as hanging or attaching to 
the  Tube  Mount.  The  angle  can  be  easily  adjusted  and  securely  fixed 
using the included M10×100 ball-lock pin. The Rigging System allows for 
up to ±20 degree tilt, in 5-degree increments. The mount is made from 
stainless steel 316 and aluminum, with stainless steel or black powder-
coated finish.

The kit includes:

The fully assembled Contour Rigging System

An M10×100 mm ball-lock pin

Tube Mount

Figure  4. The Tube Mount.

The Tube Mount enables a Contour loudspeaker to be coupled with the 
proprietary square-section Active Speaker Tubes or an industry-standard 
ø40 mm round speaker tube for deployment of a CT28 or Cannon Series 
enclosure on a free-standing base, a CT28 atop a SUB215, or a CT212 
atop a SUB2112 subwoofer. The mount attaches to the Contour Rigging 
System. The Tube Mount is made of galvanized, zinc plated and black 
or white powder coated steel.

The kit includes:

The Tube Mount adaptor

A ½"x ¾" zinc hex bolt

A ½" split locking washer

Sub Pole Cup

Square adapter for subwoofer M20 flange to Active Speaker Tube

Figure  5. Sub Pole Cup

The Sub Pole Cup is made from 4 mm steel and fits in various 1 SOUND 
subwoofers in order to mount a satellite speaker enclosure. It couples 
with all 1 SOUND Active Speaker Tubes, as well as standard round poles 
that have a M20 screw-in bolt. It is available with a black or white finish.

The kit includes:

Sub Pole Cup

Gasket (pre-installed on the Sub Pole Cup)

Passive 40 cm Speaker Tube

For mounting mounting satellite speaker enclosures atop subwoofers.

Figure  6. The 40 cm (16 in) Speaker Tube.

The 40 cm 

(≈16") 

 Speaker Tube is a simple steel square-section speaker 

pole  for  mounting  satellite  speaker  enclosures  atop  subwoofers.  It  is 
available with a black or white finish.

The kit includes:

The Speaker Tube

Summary of Contents for Contour CT212






















Reviews: