ZyXEL Communications P-871H Series Скачать руководство пользователя | Manualshive

Страница: 3 / 101

background image

P-871H Series User’s Guide

2

Interference Statements and Warnings

Interference Statements and

Warnings

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired

operations.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.

If this equipment does cause harmful interference to radio/television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Notice 1

Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.

Certifications

1

Go to www.zyxel.com

2

Select your product from the drop-down list box on the ZyXEL home page to go
to that product's page.

3

Select the certification you wish to view from this page.

«
1
2
3
4
5
...
»

Содержание P-871H Series






































































































Отзывы:

Нет отзывов

Похожие инструкции для P-871H Series

Бренд: A-Link Страницы: 8

Бренд: C-motech Страницы: 11

Бренд: Xerox Страницы: 56

Бренд: Maestro Страницы: 32

Бренд: Swann Страницы: 2

Бренд: Palm Страницы: 20

COMSPHERE 3821Plus

Бренд: Paradyne Страницы: 28

Бренд: Pantech Страницы: 118

Бренд: SimpleTech Страницы: 90

Бренд: Adeunis RF Страницы: 109

INTERNET DSL MODEMS

Бренд: Geetel Страницы: 10

Бренд: BroadMax Technology Страницы: 2

DirecWay DW4020

Бренд: Hughes Network Страницы: 102

Бренд: Elastic Networks Страницы: 30

DSL-100D - 8 Mbps DSL Modem

Бренд: D-Link Страницы: 44

Бренд: NAL Страницы: 172

Бренд: Zoomtak Telephonics Страницы: 36

Бренд: StarBand Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды