ZyXEL Communications IES-1248-51 страница 209 Скачать руководство пользователя

Страница: 209 / 385

IES-1248-51 User’s Guide

Chapter 33 Alarm

209

Figure 108

Alarm Port Setup

The following table describes the labels in this screen.

Table 62

Alarm Port Setup

LABEL

DESCRIPTION

Alarm Status

Click

Alarm Status

to go to a screen that displays the alarms that are currently

in the system (see

Section 33.2 on page 203

Alarm Event Setup

Click

Alarm Event Setup

to go to a screen where you can configure the severity

level of an alarm(s) and where the system is to send the alarm(s). See

Section

33.4 on page 206

Port

This column lists the device’s individual DSL and Ethernet interfaces.

Severity

Select an alarm severity level (critical, major, minor or info) as the threshold for

recording alarms on this port. Critical alarms are the most severe, major alarms

are the second most severe, minor alarms are the third most severe and info

alarms are the least severe.

Apply

Click

Apply

to save your changes to the IES-1248-51’s volatile memory. The

IES-1248-51 loses these changes if it is turned off or loses power, so use the

Config Save

link on the navigation panel to save your changes to the non-

volatile memory when you are done configuring.

Cancel Click

Cancel

to start configuring the screen again.

Содержание IES-1248-51


































































































































































































































































































































































































Результаты поиска

Содержание IES-1248-51

Отзывы:

Похожие инструкции для IES-1248-51

Бренды по названию

Популярные бренды

ZyXEL Communications IES-1248-51, Руководство пользователя

Результаты поиска

Содержание IES-1248-51

Отзывы:

Похожие инструкции для IES-1248-51

Бренды по названию

Популярные бренды