ZyXEL Communications IES-1248-51 страница 185 Скачать руководство пользователя

Страница: 185 / 385

IES-1248-51 User’s Guide

Chapter 28 2684 Routed Mode

185

The following table describes the labels in this screen.

Table 46

2684 Routed Domain

LABEL

DESCRIPTION

RPVC ARP Proxy

Click

RPVC ARP Proxy

to go to the screen where you can view the Address

Resolution Protocol table of IP addresses of CPE devices using 2684 routed

mode and configure how long the device is to store them (see

Section 28.4 on

page 186

Routed Gateway

Click

Routed Gateway

to go to the screen where you can configure gateway

settings (see

Section 28.5 on page 186

Routed PVC

Click

Routed PVC

to go to the screen where you can configure routed PVC

settings (see

Section 28.2 on page 182

Port

Use this drop-down list box to select a port for which you wish to configure

settings.

VPI

Type the Virtual Path Identifier for this routed PVC.

VCI

Type the Virtual Circuit Identifier for this routed PVC. The IES-1248-51 uses this

PVC channel internally.

Enter the subscriber’s CPE LAN IP address in dotted decimal notation.

NetMask

The bit number of the subnet mask of the subscriber’s IP address. To find the bit

number, convert the subnet mask to binary and add all of the 1’s together. Take

“255.255.255.0” for example. 255 converts to eight 1’s in binary. There are three

255’s, so add three eights together and you get the bit number (24).

Add Click

Add

to save your changes to the IES-1248-51’s volatile memory.

The IES-1248-51 loses these changes if it is turned off or loses power, so use

the

Config Save

link on the navigation panel to save your changes to the non-

volatile memory when you are done configuring.

Cancel Click

Cancel

to start configuring the screen again.

Index

This field displays the number of the routed PVC.

Port

This field displays the number of the ADSL port on which the routed PVC is

configured.

VPI

This field displays the Virtual Path Identifier (VPI) The VPI and VCI identify a

channel on this port.

VCI

This field displays the Virtual Circuit Identifier (VCI). The VPI and VCI identify a

channel on this port.

This field displays the subscriber’s IP address.

NetMask

This field displays the bit number of the subnet mask of the subscriber’s LAN IP

address.

Delete

Select an entry’s

Delete

check box and click

Delete

to remove the entry.

Clicking

Delete

saves your changes to the IES-1248-51’s volatile memory.

The IES-1248-51 loses these changes if it is turned off or loses power, so use

the

Config Save

link on the navigation panel to save your changes to the non-

volatile memory when you are done configuring.

Cancel Click

Cancel

to start configuring the screen again.

Содержание IES-1248-51


































































































































































































































































































































































































Результаты поиска

Содержание IES-1248-51

Отзывы:

Похожие инструкции для IES-1248-51

Бренды по названию

Популярные бренды

ZyXEL Communications IES-1248-51, Руководство пользователя

Результаты поиска

Содержание IES-1248-51

Отзывы:

Похожие инструкции для IES-1248-51

Бренды по названию

Популярные бренды