ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 182 | Manualshive

Страница: 182 / 385

ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 182

IES-1248-51 User’s Guide

182

Chapter 28 2684 Routed Mode

Figure 92

2684 Routed Mode Example

Note the following.

• The CPE device’s WAN IP (192.168.10.200 in this example) must be in the same subnet

as the gateway’s IP address (192.168.10.102 in this example).

• The IES-1248-51's management IP address can be any IP address, it doesn't have any

relationship to the WAN IP address or routed gateway IP address.

• The IES-1248-51’s management IP address should not be in the same subnet as the one

defined by the WAN IP address and netmask of the subscriber’s device. It is suggested
that you set the netmask of the subscriber’s WAN IP address to 32 to avoid this problem.

• The IES-1248-51's management IP address should not be in the same subnet range of any

RPVC and RPVC domain. It will make the IES-1248-51 confused if the IES-1248-510
receives a packet with this IP as destination IP.

• The IES-1248-51’s management IP address also should not be in the same subnet as the

one defined by the LAN IP address and netmask of the subscriber’s device. Make sure
you assign the IP addresses properly.

• In general deployment, the computer must set the CPE device’s LAN IP address

(10.10.10.10 in this example) as its default gateway.

• The subnet range of any RPVC and RPVC domain must be unique.

28.2 2684 Routed PVC Screen

Use this

screen to configure PVCs for 2684 routed mode traffic.

To open this screen, click

Advanced Application

,

2684 Routed Mode

.

«
...
180
181
182
183
184
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды