ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 151

Страница: 151 / 385

IES-1248-51 User’s Guide

Chapter 19 VLAN

151

The following table describes the labels in this screen.

19.5 VLAN Port Setting Screen

Use this screen to specify port VLAN IDs and to set whether or not Ethernet ports propagate
VLAN information to other devices.

To open this screen, click

Advanced Application

VLAN

VLAN Port Setting

Table 30

Static VLAN Setting

LABEL

DESCRIPTION

VLAN Status

Click

VLAN Status

to see which of the IES-1248-51’s ports are members of

which VLANs (see

Section 19.3 on page 148

)

VLAN Port Setting

Click

VLAN Port Setting

to specify Port VLAN IDs (PVIDs). See

Section 19.5 on

page 151

VID

This field displays the ID number of the VLAN group. Click the number to edit the

VLAN settings.

Active

This field indicates whether the VLAN settings are enabled (

Yes

) or disabled

(

Name

This field displays the descriptive name for this VLAN group.

Delete

Select the check boxes of the rule(s) that you want to remove in the

Delete

column and then click the

Delete

button.

You cannot delete a VLAN if any PVIDs are set to use the VLAN or the VLAN is

the CPU (management) VLAN.

Cancel

Click

Cancel

to clear the

Delete

check boxes.

Active

Select this check box to enable the VLAN.
You cannot disable a VLAN if any PVIDs are set to use the VLAN or the VLAN is

the CPU (management) VLAN.

Name

Enter a descriptive name for this VLAN group for identification purposes.

VLAN ID

Enter the VLAN ID for this static VLAN entry; the valid range is between 1 and

4094.

Port

The port numbers identify the IES-1248-51’s ports.

Control

Select

Fixed

for the port to be a permanent member of this VLAN group. Use the

Select All

button to include every port.

Select

Forbidden

if you want to prohibit the port from joining this VLAN group.

Use the

Select All

button to include every port.

Tagging

Select

TX Tagging

if you want the port to tag all outgoing frames transmitted

with this VLAN ID. Use the

All

button to include every port. Use the

None

button

to clear all of the ports check boxes.

Add

Click

Add

to save your settings. The VLAN then displays in the summary table

at the top of the screen.
Clicking

Add

saves your changes to the IES-1248-51’s volatile memory. The

IES-1248-51 loses these changes if it is turned off or loses power, so use the

Config Save

link on the navigation panel to save your changes to the non-

volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring the fields afresh.

Содержание IES-1248-51


































































































































































































































































































































































































Результаты поиска

Содержание IES-1248-51

Отзывы:

Бренды по названию

Популярные бренды

ZyXEL Communications IES-1248-51, Руководство пользователя

Результаты поиска

Содержание IES-1248-51

Отзывы:

Бренды по названию

Популярные бренды