ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя | Manualshive

Страница: 5 / 282

background image

Dimension ES-3148 User’s Guide

Interference Statements and Warnings

3

2

Select your product from the drop-down list box on the ZyXEL home page to go to that product's
page.

3

Select the certification you wish to view from this page.

Safety Warnings

For your safety, be sure to read and follow all warning notices and instructions.

• To reduce the risk of fire, use only No. 26 AWG (American Wire Gauge) or larger telecommunication

line cord.

• Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high

voltage points or other risks. ONLY qualified service personnel can service the device. Please contact
your vendor for further information.

• Use ONLY the dedicated power supply for your device. Connect the power cord or power adaptor to

the right supply voltage (110V AC in North America or 230V AC in Europe).

• Do NOT use the device if the power supply is damaged as it might cause electrocution.
• If the power supply is damaged, remove it from the power outlet.
• Do NOT attempt to repair the power supply. Contact your local vendor to order a new power supply.
• Place connecting cables carefully so that no one will step on them or stumble over them. Do NOT

allow anything to rest on the power cord and do NOT locate the product where anyone can walk on
the power cord.

• If you wall mount your device, make sure that no electrical, gas or water pipes will be damaged.
• Do NOT install nor use your device during a thunderstorm. There may be a remote risk of electric

shock from lightning.

• Do NOT expose your device to dampness, dust or corrosive liquids.
• Do NOT use this product near water, for example, in a wet basement or near a swimming pool.
• Make sure to connect the cables to the correct ports.
• Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device.
• Do NOT store things on the device.
• Connect ONLY suitable accessories to the device.

«
...
3
4
5
6
7
...
»

Содержание Dimension ES-3148



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dimension ES-3148

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

BiPAC 4500NZ(L)

Бренд: Billion Страницы: 146

Бренд: Ubiquiti Страницы: 23

Бренд: Oracle Страницы: 24

Бренд: XMOS Страницы: 6

Бренд: QNAP Страницы: 54

Бренд: IDT Страницы: 207

ELITENAS EN104L+(B)

Бренд: Sans Digital Страницы: 9

Turbo NAS TVS-71 Series

Бренд: QNAP Страницы: 51

Бренд: Accton Technology Страницы: 78

ISDN SOHO Router

Бренд: AOpen Страницы: 89

IE-SW-PL09M-5GC-4GT

Бренд: Weidmuller Страницы: 15

Бренд: TRENDnet Страницы: 57

Бренд: WTI Страницы: 178

JetNet 5720G-8P Series

Бренд: Korenix Страницы: 52

ROUTE FINDER RFIPSC-1

Бренд: Multitech Страницы: 54

GigaVUE H Series

Бренд: Gigamon Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды