-30
-20
-10
+0
10 Hz
100 Hz
1 KHz
10 kHz
freq. response
freq. response with low cut
�
1
2
3 4 5 6 7 8
13
9 10 11 12
19
14
15
16
17
18
20 21 22 23
24
25
26
27
28
29
30
31
(re-amplifying mode), or guitar input 1/4 inch Jack Connector type. Only one type is used at a time.
10.
FX - Activate / Deactivate FX loop. Use the FX RET pot control to adjust the signal
level that returns to the amplifier when the FX loop is active.
11.
EQ - Modern EQ setting (IN)/ Vintage EQ setting (OUT) for the Virtual Microphone.
Use the DISTANCE and ANGLE to fine tune the virtual micing
12.
GAIN panel - contains the gain controls for all channels
13.
CH1 EQ - contains the TREBLE and BASS controls for CH1 only.
14.
VOLUME panel - contains the volume controls for all channels
15.
GLOBAL PRESENCE - eq for the power amp section
16.
CH2+3 EQ panel - contains the EQ controls for CH2 and CH3
17.
ST BY - Stand By button (Engaged - RED light. Disengaged - BLUE light)
18.
POWER - Main power switch.
BACKPLATE
19.
SHIPPED WITH - mains fuse value
20.
Voltage Selector - Match the voltage to the local power grid
21.
Mains Input Socket
22.
Mains fuse - Fuse that protects the amp from wrong power input.
23.
GLOBAL FUSE 1A - Fuse that protects the amps internal components
24.
SPEAKER OUT - Standard speaker out connectors. USE ONLY ONE SPEAKER CABINET
25.
VIRTUAL MIC panel - XLR type connector for MIC SIMULATOR
balanced/unbalanced signal output and switches for MIC/LINE LEVEL and GND LIFT
26.
LINE OUT / SLAVE - standard connector for sending a signal to a slave amp
27.
FX LOOP panel standard send and return connectors for the effects
28.
PRE DI FX INSERT Insert point in the input signal chain. Use Y-cable with 1/4 “Jacks.
29.
DI MIC OUT DI balanced/unbalanced microphone level output, type XLR.
DI GND LIFT - Disconnects the contact between the ground of the device
connected on DI MIC OUT and the ground of the amplifier. This will stop
unwanted noises caused by unwanted ground loops.
30.
FOOTSWITCH - DIN 8 connector for the supplied Footswitch
FRONTPLATE
1.
GROUND LIFT- Disconnects the contact between the ground of the sound source and the
ground of the amplifier. This will stop unwanted noises caused by unwanted ground loops.
2.
DI FX - when using the DI MIC OUT output on the back of the amp, the signal from your
instrument will pass straight through unaltered unless this switch is engaged. When
engaged it activates the PRE DI FX INSERT loop on the back the amp. The signal will then be
processed by the effects present in the PRE DI FX INSERT loop. When a Y-cable is inserted
and external effects are present in the PRE
DI FX INSERT loop, these effects will always
feed the Pre-Amplifying stage of the amp
regardless of the state of this switch.
3.
High Pass Filter - a switch common
for all tree channels. In the out position
you have a bigger bass and loser feel
and in the in position things are tighter
and more in your face with less extended
lows and more upper presence.
4.
OPEN - a switch for dynamic compressor type effect. In the OUT position OPEN
emulates a compressor ( adds soft clipping and compression). There will be a little
drop in volume when the switch is in the OUT position due to the added compression.
Just turn the volume up a little to make up for the difference.
5.
CH - is a non latching switch that cycles the channels.
6.
PLEXI - a mode that is voiced to please players who love that wide open 60's British
sound. This is also a great platform to push with your favorite pedal in front of the amplifier.
PLEXI mode is a lower gain channel than MODERN (PLEXI button toggles between plexi
and modern). Like the older amps it emulates, the louder you turn it up the better it sounds.
7.
BOOST - is a non latching switch Increased sensitivity (more gain) for CH2 and CH3.
8.
BRGT - High frequencies are enriched when the CH1 (clean channel) is switched on.
9.
LINE IN / INST - Combined connector for balanced / unbalanced line input type XLR