Mat.-Nr. 00104565/5/P- 05.10
SensControl II Lighting management
3 EN
Setting constant lighting control
Modifying the set value for constant lighting control
1.
Press both keys simultaneously and hold for 8 seconds.
a
The LED lights up.
2.
With single-channel version:
Press and hold upper key until the desired illuminance level is set.
a
LED flashes rapidly until max. or min. value is reached.
3.
With dual-channel version:
Press and hold upper key until the desired illuminance level is set for indirect light.
Press and hold lower key until the desired illuminance level is set for direct light.
a
LED flashes rapidly until max. or min. value is reached.
4.
Release the key and press and hold again to alternate the direction of adjustment.
5.
Press both keys simultaneously and hold for 8 seconds to permanently save the
setting.
a
The LED extinguishes.
Activating/deactivating constant lighting control
1.
Press both keys simultaneously and hold for 8 seconds.
a
LED lights up.
2.
Briefly release both keys and press again simultaneously, holding for 5 seconds.
a
LED flashes slowly.
3.
Press upper key 3 times
to deactivate the constant lighting control.
- or -
Press upper key 4 times
to activate the constant lighting control.
a
LED flashes 3 or 4 times to confirm.
4.
Press both keys simultaneously and hold for 8 seconds to permanently save the
setting.
a
The LED extinguishes.
Setting presence detection
Modifying delay time or deactivating presence detection
1.
Press both keys simultaneously and hold for 8 seconds.
a
LED lights up.
2.
Briefly release both keys and press again simultaneously, holding for 5 seconds.
a
LED flashes slowly.
3.
To set the delay time with the
lower key
:
•
Press
once
for 10 seconds delay time (demo mode)
•
Press
twice
for 1 minute delay time
•
Press
three times
for 5 minutes delay time
•
Press
four times
for 15 minutes delay time
•
Press
five times
for 30 minutes delay time
•
Press
six times
to deactivate presence detection
a
LED flashes 1 to 6 times to confirm.
4.
Press both keys simultaneously and hold for 8 seconds to permanently save the
setting.
a
The LED extinguishes.
Tip
Stand next to the luminaire when setting the constant lighting control and make
sure that the sensor is not blocked.
SensControl II.pdf 9
SensControl II.pdf 9
10.06.2010 11:48:00
10.06.2010 11:48:00
SensControl II Lighting management
2 EN
www.zumtobel.com
Operating SensControl II
Operation of SensControl II is via keys on the luminaire. The functions of the keys
differ according to appearance:
Parameters and factory settings
The following parameters are available for individual adjustment of functions:
Modifying settings
Operation
Single-channel version
without separation of
indirect/direct light
Dual-channel version
with separate indirect/direct light
Indirect lighting
Direct lighting
Switch on luminaire
p
Press lower/upper key.
p
Briefly press upper key.
p
Briefly press lower key.
Switch off luminaire
p
Press lower key.
Manually adjust illuminance
(dimming)
p
Press and hold upper
key until the desired
illuminance level is set.
p
Press and hold upper
key until the desired
illuminance level is set.
p
Press and hold lower
key until the desired
illuminance level is set.
During dimming take care that you do not press both
keys simultaneously, as in this case SensControl II
switches to setting mode.
a
LED flashes rapidly until max. or min. value is reached.
p
Release the key and press and hold again to alternate the direction of adjustment.
The set value for constant lighting control is automatically restored following a
longer period of absence (at least 4 hours) or following a mains disconnection.
Tip
Unplug the power
supply and connect
again while pressing
the key to reset the
factory settings.
a
LED flashes once to
confirm.
Parameter
Adjustable values
Factory setting
Constant lighting control
activated/deactivated
activated
Set value for constant
lighting control
5 - 100 %
Delay time
10 seconds (demo mode),
1, 5, 15, 30 minutes,
Presence detection deactivated
15 minutes
Control
semi-automatic/ fully
automatic
fully automatic
Lockout
activated/deactivated
activated
Tip
If you do not press a key within a twenty second period during adjustment of
constant lighting control, presence detection, lockout or automatic control,
SensControl II switches back to operating mode and the modifications are not
saved. If you have pressed keys erroneously, wait 20 seconds and repeat the
adjustment.
SensControl II.pdf 8
SensControl II.pdf 8
10.06.2010 11:47:59
10.06.2010 11:47:59
3 EN
SensControl II Lighting management
2 EN
www.zumtobel.com
Operating SensControl II
Operation of SensControl II is via keys on the luminaire. The functions of the keys
differ according to appearance:
Parameters and factory settings
The following parameters are available for individual adjustment of functions:
Modifying settings
Operation
Single-channel version
without separation of
indirect/direct light
Dual-channel version
with separate indirect/direct light
Indirect lighting
Direct lighting
Switch on luminaire
p
Press lower/upper key.
p
Briefly press upper key.
p
Briefly press lower key.
Switch off luminaire
p
Press lower key.
Manually adjust illuminance
(dimming)
p
Press and hold upper
key until the desired
illuminance level is set.
p
Press and hold upper
key until the desired
illuminance level is set.
p
Press and hold lower
key until the desired
illuminance level is set.
During dimming take care that you do not press both
keys simultaneously, as in this case SensControl II
switches to setting mode.
a
LED flashes rapidly until max. or min. value is reached.
p
Release the key and press and hold again to alternate the direction of adjustment.
The set value for constant lighting control is automatically restored following a
longer period of absence (at least 4 hours) or following a mains disconnection.
Tip
Unplug the power
supply and connect
again while pressing
the key to reset the
factory settings.
a
LED flashes once to
confirm.
Parameter
Adjustable values
Factory setting
Constant lighting control
activated/deactivated
activated
Set value for constant
lighting control
5 - 100 %
Delay time
10 seconds (demo mode),
1, 5, 15, 30 minutes,
Presence detection deactivated
15 minutes
Control
semi-automatic/ fully
automatic
fully automatic
Lockout
activated/deactivated
activated
Tip
If you do not press a key within a twenty second period during adjustment of
constant lighting control, presence detection, lockout or automatic control,
SensControl II switches back to operating mode and the modifications are not
saved. If you have pressed keys erroneously, wait 20 seconds and repeat the
adjustment.
SensControl II.pdf 8
SensControl II.pdf 8
10.06.2010 11:47:59
10.06.2010 11:47:59
