manualshive.com logo in svg

Zte ZXR10 GER, Руководство пользователя

Поделиться
Скачать
Zte ZXR10 GER Скачать руководство пользователя страница 52

 

ZXR10 GER (V2.6.03) General Excellent Router User Manual Volume-I

 

 

30      

Confidential and Proprietary Information of ZTE CORPORATION 

RE-02CE3-75 

ZXR10 GER system has two port channelized E3 interface card 
which can be inserted in any one of eight slots. This connects 

with the SMP board through the backplane. 
Figure 18 shows the RE-02CE3-75 card. 

F

I G U R E  

1 8

   

R E - 0 2 C E 3 - 7 5

 

C

A R D

 

 

RE-02CE3-75 card provides two E3/T3 interfaces. This adopts 
the CC-4 connectors and provides 75 ohm coaxial cable 
interfaces for users. 
There are three LED indicators. Table 25 shows their functions. 

T

A B L E  

2 5

   

R E - 0 2 C E 3 - 7 5

 

C

A R D  

I

N D I C A T O R S

 

Indicators 

Function Description 

RUN 

This is constantly on if the interface card is working 

normally, and this goes off if the interface card fails. 

DATA per 

port 

This is constantly on in the case of data sending and 

receiving and this is off in the case if data sending or 

receiving fails. 

LINK per port 

This is constantly on in the case of successful PPP 

link setup, and This is off in the case of PPP link 

setup failure. 

RE-02GE 

This is a two-port GE electrical/ optical interface board, providing 
two 10/100/1000BASE-T Ethernet electrical interfaces of RJ45 or 

providing two 1000BASE-X Ethernet optical interfaces of SFP. 
Maximum transmission of the optical interface is 120km; board 
compliances with IEEE802.3. This board only supports two GE 

Ethernet interfaces, so choose either  of  port  (electrical or 
optical). 

Definition 

Panel 

Interfaces 

Indicators 

Definition 

Specification 

Содержание ZXR10 GER





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды