Zte ZXR10 5900E Series Скачать руководство пользователя страница 197

Страница: 197 / 226

Chapter 18 TCP6 Configuration

18.3 TCP6 Maintenance and Diagnosis

To view the operation status of the TCP6 on the ZXR10 5900E, run the following

commands:

Command

Function

ZXR10#

show tcp6 brief

Displays the brief information of all

TCP6 connections.

ZXR10#

show tcp6 config

Displays the TCP6 configuration

parameters.

ZXR10#

show tcp6 statistics

Displays the TCP6 statistics.

ZXR10#

show tcp6 tcb

tcb-index

Displays the parameters of a

specific TCP connection.

The following is a sample output from the

show tcp6 brief

command:

ZXR10#show tcp brief

TCB

Local Address

Foreign Address

State

2001::1:23

2001::10:3183

ESTAB

2001::1:23

2001::10:3182

ESTAB

2001::1:23

2001::6:1380

ESTAB

Parameter descriptions are as follows:

Command Output

Description

2001::1.23 2001::10.2382 ESTAB

The index of the current control block is 10.

Local Address: Local address and the port.

Foreign Address: Remote address and the

port.

State: State of the TCP connection.

The following is a sample output from the

show tcp6 config

command:

ZXR10#show tcp6 config

IPv6 TCP SYNWAIT:

IPv6 TCP FINWAIT:

675

IPv6 TCP QUEUEMAX:

IPv6 TCP WINDOWSIZE:

65535

Parameter descriptions are as follows:

Command Output

Description

TCP SYNWAIT: 75

TCP6 connection SYN packet timeout time. Unit:

second.

TCP FINWAIT: 675

TCP6 connection FIN packet timeout time. Unit:

second.

18-3

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Содержание ZXR10 5900E Series



































































































































































































































Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды

Zte ZXR10 5900E Series, Руководство по настройке

Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды