Zte ZXMW NR8250 Скачать руководство пользователя страница 90

Страница: 90 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

2.4.13 402 MP voltage abnormal

Alarm Property

Alarm Code: 402

Alarm Information: This alarm is reported when the MP voltage is out of range and

cleared when the voltage becomes normal.

Alarm Level: Minor

Alarm Type: Environment Alarm

Sub-code Description

Sub-code 0: Overvoltage

Sub-code 1: Undervoltage

Effect on the System

The power supply of the board is affected, and the board cannot bear any service.

Possible Causes

When the MP voltage reported by the PM board exceeds the upper threshold, it is

over-voltage, and the voltage will be restored when the voltage is lower than the upper

threshold.

When the MP voltage reported by the PM board is lower than the lower threshold, it

is under-voltage, and the voltage will be restored when the voltage exceeds the lower

threshold.

Handling Procedure

Replace the PM board.

2.4.14 4020 outdoor battery dry contact alarm

Alarm Property

Alarm Code: 4020

Alarm Information: battery or storage battery was in fault

Alarm Level: Major

Alarm Type: Environment Alarm

Sub-code Description

None

Effect on the System

outdoor machine cabinet is abnormal ,and it does not affect the system.

2-76

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды