Zte ZXMW NR8250 Скачать руководство пользователя страница 81

Страница: 81 / 124

Chapter 2 Alarm

2.3.10 6213 Board inserted incorrectly

Alarm Property

Alarm Code: 6213

Alarm Information: When the main control board detects that the board inserted at

front-end differs from the actually configured board, this alarm is reported.

Alarm Level: Major

Alarm Type: Handling Alarm

Sub-code Description

Sub-code 1: The board actually inserted is different from that configured in the network

management system.

Sub-code 2: The type of the board actually inserted is different from that configured

in the network management system.

Effect on the System

The board cannot operate properly, and the services carried by the board are interrupted.

Possible Causes

The board type configuration at NetWork Management is incorrect, or the board is

incorrectly inserted.

Handling Procedure

On the LMT, select

Setup > Shelf

and check whether the board configuration is correct.

If yes, go to step 2.

If no, correct the configuration.

Replace the incorrect boards.

2.3.11 6214 Software version abnormal

Alarm Property

Alarm Code: 6214

Alarm Information: If the software version consistency check indicates that the version

in software package does not exist on the disk or is damaged, this alarm is reported.

Alarm Level: Major

Alarm Type: Handling Alarm

Sub-code Description

Sub-code 1: The active software package is incorrect

Sub-code 2: The running patch package of the active software package is incorrect

Sub-code 3: The standby patch package of the active software package is incorrect

2-67

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды