Zte ZXMW NR8250 Скачать руководство пользователя страница 24

Страница: 24 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

136183808. E1-16 port (LMT displays “E1-30”)

136249344. E1-16 port (LMT displays “E1-31”)

136314880. E1-16 port (LMT displays “E1-32”)

268500992. optical port 1 (LMT displays “STM1-1”);

268566528. optical port 2 (The rate is STM1 and LMT displays “STM1-2”.);

335675392. optical port 2 (The rate is STM4 and LMT displays “STM4-2”);

335680000.

optical port 2, path 1 (The rate is STM4 and LMT displays

“STM4-Channel-1”.);

335679616.

optical port 2 , path 2 (The rate is STM4 and LMT displays

“STM4-Channel-2”.);

335679744.

optical port 2, path 3 (The rate is STM4 and LMT displays

“STM4-Channel-3”.);

335679872.

optical port 2, path 4 (The rate is STM4 and LMT displays

“STM4-Channel-4”.).

Effect on the System

Traffic is interrupted when the wireless link port is in loopback status.

Possible Causes

The loopback function is enabled for testing or maintenance.

The board that reports the alarm is faulty.

Handling Procedure

Check whether loopback is configured for test or maintenance.

If yes, after the maintenance or test is completed, disable the loopback function.

(Path:

Maintenance > TDM Traffic

If no, go to step 2.

The RTUA/RTUB/RTUC/RTUH board of NR8250 equipment is faulty. Replace the

board.

2.1.12 134237782 SNCP route setting alarm

Alarm Property

Alarm Code: 134237782

Alarm Information: The alarm is reported if the SNCP route setting fails.

Alarm Level: Critical

Alarm Type: Equipment Alarm

Sub-code Description

None

2-10

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды